Hi Christoph!

I had the same problem:
http://groups.google.com/group/comp....f3fb33df6/de97

I have D201GLY and D201GLY2.

Try OpenBSD 4.2 it works on both mainboards.

I didnt try to install OpenBSD 4.3 jet.


Regards,
TomazZ



Christoph Müllner je napisal:
> Hi!
>
> I've tried to install OpenBSD 4.3 on a pc but unfortunately was not able
> to boot neither the i386 nor the amd64 install43 CD.
> The PC is a Intel D201GLY2
> (http://www.intel.com/products/mother...GLY2/index.htm) mainboard
> (Celeron 220 @ 1.2 ghz) with a CDROM and a 10GB (western digital) hd on
> the IDE-port. Furthermore there is a SATA-harddisk (samsung 500GB)
> connected on the first SATA-port and a IDE-controller (Sil 0680) plugged
> into the PCI port (with a western digital 250GB harddisk).
>
> After some attempts to install OpenBSD I was able to successfully
> install Debian Etch and run "lspci -vv" on it. The output of this can be
> found below to get some more information about the system. The FreeBSD
> 7.0 cdrom is also able to boot this machine, but I've not tried to
> install it on the system.
>
> My question is: Is there a possibility to install OpenBSD on this
> machine? If yes how can I do this?
>
> I would be glad if someone could please help me.
>
> Best regards,
> Christoph
>
>
> Here are the things I've tried:
>
> *) When booting the i386 CD (after pressing the reset-button) I get the
> message:
>
> CD-ROM: 90
> Loading /4.3/AMD64/CDBOOT
> probing: pc0 mem[639K 944M 11M 532K a20=on]
> disk: hd0+* hd1+
>
> (then the screen gets cleared and the following occours
>
> trap: 0(0): invalid opcode fault
> cn_tab=0x4ae40
> eax 4a023 ecx 1 edx 4a023 ebx 0
> esp ff58 ebp 0 esi 0 edi 0
> eip 3 eflags 10007 cs 8 ss 10
> ds 10 es 10 fs 10 gs 10
> Code dump [0x3]:
> ...
> ...
> ...
>
>
> *) When booting the amd64 CD after pushing the reset-button, I get a
> freeze at
>
> CD-ROM: 90
> Loading /4.3/AMD64/CDBOOT
> probing: pc0 mem[639K 944M 11M 532K a20=on]
> disk: hd0+* hd1+
>
> with the cursor after the last '+'
>
> *) When booting the i386 CD or the amd64 CD after power off, the problem
> above doesn't occour and the disk-line says:
> disk: hd0+* hd1+* hd2* cd0
> and starts booting. After a few seconds it hangs with the line
> (typewritten, because I've no null-modem-cable):
>
> wd2 at pciide2 channel0 drive 0: <WD2500JB-00GVC0>
> wd2: 16-sector PIO, LBA48, 238475MB, 488397168 sectors
> wd2(pciide2:0:0): using PIO mode 4, Ultra-DMA mode 5
> pciide2: channel 1 configured to native-PCI mode
> ppb1 at pci0 dev 31 function 0 "SiS PCI-PCI" rev 0x00
> pci2 at ppb1 bus 2
> usb1 at ohci0: USB revision 1.0
> uhub1 at usb1 "SiS OHCI root hub" rev 1.00/1.00 addr 1
> usb2 at ohci0: USB revision 1.0
> uhub2 at usb1 "SiS OHCI root hub" rev 1.00/1.00 addr 1
> usb3 at ohci0: USB revision 1.0
> uhub3 at usb1 "SiS OHCI root hub" rev 1.00/1.00 addr 1
> isa0 at mainbus0
> com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
> pckbc0 at isa0 port 0x60/5
> pckbd0 at pckbc0 (kbd slot)
> pckbc0: using irq 1 for kbd slot
> wskbd0 at pckbd0: console keyboard, using wsdisplay0
> rd0: fixed 4480 blocks
> wd0(pciide0:0:1): timeout
> type: ata
> c_bcount: 512
> c_skip: 0
> pciide:0:0:1: bus-master DMA error: missing interrupt, status=0x61
>
> Please note that it makes no difference if I plug out the PCI-card
> (IDE-controller).
> I found a pointer to
> http://archives.neohapsis.com/archiv...1-12/1351.html which
> helps to avoid the error, but disabling pciide means no harddisks at all.
>
> *) I have successfully installed Debian Etch on this machine and the
> output of lspci -vv is:
>
> 00:00.0 Host bridge: Silicon Integrated Systems [SiS] Unknown device
> 0662 (rev 01)
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort+ >SERR- <PERR-
> Latency: 128
> Region 0: Memory at 48000000 (32-bit, non-prefetchable) [size=32M]
> Capabilities: [c0] AGP version 3.5
> Status: RQ=32 Iso- ArqSz=2 Cal=3 SBA+ ITACoh- GART64- HTrans- 64bit-
> FW+ AGP3+ Rate=x4,x8
> Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
>
> 00:01.0 PCI bridge: Silicon Integrated Systems [SiS] SiS AGP Port
> (virtual PCI-to-PCI bridge) (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
> <MAbort- >SERR- <PERR-
> Latency: 0, Cache Line Size: 64 bytes
> Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
> I/O behind bridge: 00001000-00001fff
> Memory behind bridge: 4a000000-4a0fffff
> Prefetchable memory behind bridge: 40000000-47ffffff
> Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
> <MAbort+ <SERR- <PERR-
> BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
>
> 00:02.0 ISA bridge: Silicon Integrated Systems [SiS] SiS964 [MuTIOL
> Media IO] (rev 36)
> Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
>
> 00:02.5 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE] (rev
> 01) (prog-if 80 [Master])
> Subsystem: Intel Corporation Unknown device d61f
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 128
> Region 0: I/O ports at <unassigned>
> Region 1: I/O ports at <unassigned>
> Region 2: I/O ports at <unassigned>
> Region 3: I/O ports at <unassigned>
> Region 4: I/O ports at 2320 [size=16]
> Capabilities: [58] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:02.7 Multimedia audio controller: Silicon Integrated Systems [SiS]
> AC'97 Sound Controller (rev a0)
> Subsystem: Intel Corporation Unknown device d61f
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 128 (13000ns min, 2750ns max)
> Interrupt: pin C routed to IRQ 233
> Region 0: I/O ports at 2100 [size=256]
> Region 1: I/O ports at 2280 [size=128]
> Capabilities: [48] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=55mA
> PME(D0-,D1-,D2-,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:03.0 USB Controller: Silicon Integrated Systems [SiS] USB 1.0
> Controller (rev 0f) (prog-if 10 [OHCI])
> Subsystem: Intel Corporation Unknown device d61f
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR+ FastB2B-
> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 64 (20000ns max)
> Interrupt: pin A routed to IRQ 185
> Region 0: Memory at 4a104000 (32-bit, non-prefetchable) [size=4K]
>
> 00:03.1 USB Controller: Silicon Integrated Systems [SiS] USB 1.0
> Controller (rev 0f) (prog-if 10 [OHCI])
> Subsystem: Intel Corporation Unknown device d61f
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR+ FastB2B-
> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 64 (20000ns max)
> Interrupt: pin B routed to IRQ 193
> Region 0: Memory at 4a103000 (32-bit, non-prefetchable) [size=4K]
>
> 00:03.2 USB Controller: Silicon Integrated Systems [SiS] USB 1.0
> Controller (rev 0f) (prog-if 10 [OHCI])
> Subsystem: Intel Corporation Unknown device d61f
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR+ FastB2B-
> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 64 (20000ns max)
> Interrupt: pin C routed to IRQ 201
> Region 0: Memory at 4a102000 (32-bit, non-prefetchable) [size=4K]
>
> 00:03.3 USB Controller: Silicon Integrated Systems [SiS] USB 2.0
> Controller (prog-if 20 [EHCI])
> Subsystem: Silicon Integrated Systems [SiS] USB 2.0 Controller
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR+ FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32 (20000ns max), Cache Line Size: 32 bytes
> Interrupt: pin D routed to IRQ 209
> Region 0: Memory at 4a101000 (32-bit, non-prefetchable) [size=4K]
> Capabilities: [50] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
> PME(D0+,D1-,D2-,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:04.0 Ethernet controller: Silicon Integrated Systems [SiS] SiS900 PCI
> Fast Ethernet (rev 91)
> Subsystem: Intel Corporation Unknown device d61f
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 128 (13000ns min, 2750ns max)
> Interrupt: pin A routed to IRQ 217
> Region 0: I/O ports at 2000 [size=256]
> Region 1: Memory at 4a100000 (32-bit, non-prefetchable) [size=4K]
> Expansion ROM at 4a120000 [disabled] [size=128K]
> Capabilities: [40] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:05.0 IDE interface: Silicon Integrated Systems [SiS] SATA (rev 01)
> (prog-if 85 [Master SecO PriO])
> Subsystem: Intel Corporation Unknown device d61f
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 128
> Interrupt: pin A routed to IRQ 225
> Region 0: I/O ports at 2348 [size=8]
> Region 1: I/O ports at 235c [size=4]
> Region 2: I/O ports at 2340 [size=8]
> Region 3: I/O ports at 2358 [size=4]
> Region 4: I/O ports at 2310 [size=16]
> Region 5: I/O ports at 2200 [size=128]
> Capabilities: [58] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:06.0 RAID bus controller: Silicon Image, Inc. PCI0680 Ultra ATA-133
> Host Controller (rev 02)
> Subsystem: Silicon Image, Inc. Winic W-680 (Silicon Image 680 based)
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 128, Cache Line Size: 4 bytes
> Interrupt: pin A routed to IRQ 225
> Region 0: I/O ports at 2338 [size=8]
> Region 1: I/O ports at 2354 [size=4]
> Region 2: I/O ports at 2330 [size=8]
> Region 3: I/O ports at 2350 [size=4]
> Region 4: I/O ports at 2300 [size=16]
> Region 5: Memory at 4a105000 (32-bit, non-prefetchable) [size=256]
> Expansion ROM at 4a180000 [disabled] [size=512K]
> Capabilities: [60] Power Management version 2
> Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=2 PME-
>
> 00:1f.0 PCI bridge: Silicon Integrated Systems [SiS] PCI-to-PCI bridge
> (prog-if 00 [Normal decode])
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
> <MAbort- >SERR- <PERR-
> Latency: 0, Cache Line Size: 64 bytes
> Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
> Memory behind bridge: 3c000000-3c0fffff
> Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
> <MAbort+ <SERR- <PERR-
> BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
> Capabilities: [d0] Express Root Port (Slot+) IRQ 0
> Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag+
> Device: Latency L0s <64ns, L1 <1us
> Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
> Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
> Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
> Link: Supported Speed 2.5Gb/s, Width x16, ASPM L0s L1, Port 0
> Link: Latency L0s <1us, L1 <2us
> Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
> Link: Speed 2.5Gb/s, Width x0
> Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
> Slot: Number 0, PowerLimit 75.000000
> Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
> Slot: AttnInd Off, PwrInd Off, Power-
> Root: Correctable- Non-Fatal- Fatal- PME-
> Capabilities: [a0] Message Signalled Interrupts: Mask- 64bit- Queue=0/0
> Enable+
> Address: fee00000 Data: 40b1
> Capabilities: [f4] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 01:00.0 VGA compatible controller: Silicon Integrated Systems [SiS]
> 661/741/760/761 PCI/AGP VGA Display Adapter (rev 04) (prog-if 00 [VGA])
> Subsystem: Intel Corporation Unknown device d61f
> Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Interrupt: pin A routed to IRQ 10
> BIST result: 00
> Region 0: Memory at 40000000 (32-bit, prefetchable) [size=128M]
> Region 1: Memory at 4a000000 (32-bit, non-prefetchable) [size=128K]
> Region 2: I/O ports at 1000 [size=128]
> Capabilities: [40] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [50] AGP version 3.0
> Status: RQ=256 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit-
> FW- AGP3+ Rate=x4,x8
> Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>