Matthew Piechotta wrote:
> I am having a heck of a time trying to discern what is wrong with one of my
> K100s
>
> When attempting to install HP-UX, the system boots, but eventually displays
> the following on the console:
>
> ***
>
> Booting...
> Boot IO Dependent Code (IODC) revision 0
>
>
> HARD Booted.
>
> ISL Revision A.00.43 Apr12, 2000
>
> ISL booting hpux (;0):INSTALL
>
> Boot
> : disk(8/12/5.2.0.0.0.0.0;0):INSTALL
> 9707284 + 1122304 + 691712 start 0x14d568
> FLT CBFB
> ******* Unexpected HPMC. Processor HPA 0xfffa0000 *******
> GENERAL REGISTERS:
> r00/07 00000000 0010C800 00452F94 02A46800 00000089 00000000 00000000
> 02971280
> r08/15 00000001 00000002 00000003 0FD1BE2C 0014D568 FFFFFFFF 00000801
> 000331D0
> r16/23 00000001 00030720 00000008 FFB40838 00000008 00000001 00081003
> FFB40800
> r24/31 00000000 00000045 FFB40845 00A73268 00000000 00000038 7FFF0CB0
> 00081003
> CONTROL REGISTERS:
> sr0/7 00000000 00000000 00000000 00000000 00000000 0000224D 00002247
> 00000000
> pcq 00000000.0010CF84 00000000.0010CF88 isr = 00000000 ior = 00452F94
> pid1/4 0000 0000 0000 0000 ipsw = 0004000F iva = 00029800 sar = 0F ccr = C0
> tr0/7 00982AA8 00035800 FFFFFFF0 00000000 01830930 15F168E5 0009BB68
> 7FFF0BB8
> rctr = 00000000 itmr = 160B5F84 eiem = FFFFFFF0 eirr = 80000008 iir =
> E840C002
> cr1/7 00000000 00000000 00000000 00000000 00000000 00000000 00000000
> MACHINE CHECK PARAMETERS:
> Check Type = 20000000 CPU STATE = 9E000004 Cache Check = 00000000
> TLB Check = 00000000 Bus Check = 0020000C PIM State = ? SIU Status =
> ????????
> Detected by 00000000 Assists = 00000000 Processor = 00000000
> Assist ID = 00000000 Slave Addr = FFFA0000 Master Addr = 00000000
>
>
> trap type 1 (HPMC), pcsq.pcoq = 0.10cf84, isr.ior = 0.452f94
> @(#) $Revision: vmunix: vw: -proj selectors: CUPI80_BL2000_1108 -c
> 'Vw
> for CUPI80_BL2000_1108 build' -- cupi80_bl2000_1108 'CUPI80_BL2000_1108'
> Wed N
> ov 8 19:05:38 PST 2000 $High-priority machine check: (display==0xd910,
> flags==0
> x0)
> * CPU State 0x9e000004
> * Detected By 0x0
> * Bus Check 0x20000c
> * Slave Address 0xfffa0000
> WARN E000
>
> *** A system crash has occurred. (See the above messages for details.)
> *** The system is now preparing to dump physical memory to disk, for use
> *** in debugging the crash.
>
> ERROR: Your system crashed before I/O and dump configuration was complete.
> A crash dump cannot be taken under these circumstances without
> special configuration. Contact your HP support representative.
>
> *****
>
> Can anyone make heads or tails of this?
>
> Thank you all very much, your help is greatly appreciated.
>
>
Are you trying to boot the machine with an 11i TCOE release? Try the
server version. I believe the 11i workstation release expects a PA2.0
system and the K100 is PA1.[2-3]