Josh Grosse wrote:
> On Thu, 15 Feb 2007 20:32:42 +0100, Peter van Oord van der Vlies wrote:
>
>> Hello,
>>
>> I have setup 2 HP DL360 G5 with serial ATA drives.
>>
>> Both are setup with openbsd 4.0 and disk mirror by Raidframe.
>> Now almost everytime when i reboot the machine(they are not in
>> production yet) i get directly after the reboot command a panic.
>>
>> Now i was reading on the internet that is not recommended to have swap
>> on a mirror or the same mirror as the rest.
>> So after the reboot now the system always comes up with a dirty paritity
>> and starts building again(takes a while to complete).
>> Also i see the message savecore: no dump device configured. Why is that ?
>>
>> The question: Is this normal when swap is not outside the raid set or on
>> the same raid set as the rest ?
>
> Peter,
>
> A little information on your configuration will go a long way towards
> helping you.
>
> It appears, from your description, that you are getting a repeatable
> panic. Nobody is going to be able to help you with that, unless you are
> able to provide minimal information: what the panic is, what the backtrace
> shows, etc.
>
> I can answer the dump device question, as I had already investigated it.
> You can see the details by reading misc@ archives. In brief: When you
> have root on RAID, you cannot dump core. It doesn't matter if
> your swap is in a RAID set or on a standard device.
>
> As to your continuing problem with "dirty" areas after reboot, it could
> certainly be the panic. If you are able to shutdown and boot without
> panic, but still going through parity rebuilding, then you have a
> configuration problem.
>
> Post the output of disklabel for all disks (real and RAIDFrame), and the
> output for fdisk for each disk if your architecture uses MBR.
>

I still had a swap on both disks so i use that one now and disabled the
swap on raid0.
It seems to work..

Here is the information you want(the fault and trace is below):

# disklabel -E wd0
# Inside MBR partition 3: type A6 start 63 size 156296322

Treating sectors 63-156296385 as the OpenBSD portion of the disk.
You can use the 'b' command to change this.

Initial label editor (enter '?' for help at any prompt)
> p
device: /dev/rwd0c
type: ESDI
disk: ESDI/IDE disk
label: ST3808110AS
bytes/sector: 512
sectors/track: 63
tracks/cylinder: 16
sectors/cylinder: 1008
cylinders: 16383
total sectors: 156301488
free sectors: 0
rpm: 3600

16 partitions:
# size offset fstype [fsize bsize cpg]
a: 2097585 63 4.2BSD 2048 16384 328 # Cyl
0*- 2080
b: 4194288 2097648 swap # Cyl 2081
- 6241
c: 156301488 0 unused 0 0 # Cyl 0
-155060
d: 150004449 6291936 RAID # Cyl 6242
-155055*

# disklabel -E wd1
# Inside MBR partition 3: type A6 start 63 size 156296322

Treating sectors 63-156296385 as the OpenBSD portion of the disk.
You can use the 'b' command to change this.

Initial label editor (enter '?' for help at any prompt)
> p
device: /dev/rwd1c
type: ESDI
disk: ESDI/IDE disk
label: ST3808110AS
bytes/sector: 512
sectors/track: 63
tracks/cylinder: 16
sectors/cylinder: 1008
cylinders: 16383
total sectors: 156301488
free sectors: 0
rpm: 3600

16 partitions:
# size offset fstype [fsize bsize cpg]
a: 2097585 63 4.2BSD 2048 16384 328 # Cyl
0*- 2080
b: 4194288 2097648 swap # Cyl 2081
- 6241
c: 156301488 0 unused 0 0 # Cyl 0
-155060
d: 150004449 6291936 RAID # Cyl 6242
-155055*

# raidctl -sv raid0
raid0 Components:
/dev/wd0d: optimal
/dev/wd1d: optimal
No spares.
Component label for /dev/wd0d:
Row: 0, Column: 0, Num Rows: 1, Num Columns: 2
Version: 2, Serial Number: 20070200, Mod Counter: 110
Clean: No, Status: 0
sectPerSU: 128, SUsPerPU: 1, SUsPerRU: 1
Queue size: 100, blocksize: 512, numBlocks: 150004352
RAID Level: 1
Autoconfig: Yes
Root partition: Yes
Last configured as: raid0
Component label for /dev/wd1d:
Row: 0, Column: 1, Num Rows: 1, Num Columns: 2
Version: 2, Serial Number: 20070200, Mod Counter: 110
Clean: No, Status: 0
sectPerSU: 128, SUsPerPU: 1, SUsPerRU: 1
Queue size: 100, blocksize: 512, numBlocks: 150004352
RAID Level: 1
Autoconfig: Yes
Root partition: Yes
Last configured as: raid0
Parity status: clean
Reconstruction is 100% complete.
Parity Re-write is 100% complete.
Copyback is 100% complete.


The crash:

uvm_fault(0xd0821a20, 0xe9dbd00, 0, 1) -> e
kernel: page fault trap, code=0
Stopped at pmap_page_remove_86+0x125: movl 0(%eax,%edx,4),%eax


show panic:
the kernel did not panic


trace:
pmap_page_remove_86(d0cba46,d04b6474,8,246,d7fd738 a8) at
pmap_page_remove_86+0x125
uvm_vnp_terminate(d8135138,0,0,0,0,14,d81869d8,9) at uvm_vnp_terminate+0x36b
uvm_attach(d8135138,0,b7,0,d7f4f89c) at uvn_attach+0x2d1
uvmspace_free(d7f4f89c,6,d085f740) at uvmspace_free+0x10d
uvm_exit(d7f3d87c,d038e561,8,286) at uvm_exit+0x1a
reaper(d81869d8) at reaper+0x9a
Bad frame pointer: 0xd0989eb8