Hi all!

few days ago I installed Etch on my computer and am now stuck with the
DVD writer. The installer had no issue booting from the drive and do the
installation. But the installed system no longer detects that a DVD
drive is there.

The DVD is a SATA drive from LG, connected to a JMicron SATA/IDE JMB 363
(according mainboard manual) controller. I'm wondering that the Etch
installer was able to run this combination, whereas the Etch
installation does not...

Searching the net about that issue I'm even more wondering that the
installation worked, after I read that support for the JMicron
controller was introduced with 2.6.19. Don't get me wrong, I'm not
complaining that the installation worked that smoothly... :-)

Booting Knoppix 5.2 live CD works well, with the DVD being fine... but
that's based on 2.6.19 anyway...

Changing BIOS settings for the JMicron controller from IDE to AHCI
didn't made a difference.

Has anyone seen this before and ideas how to get Etch detect my DVD drive?

Thanks & best regards,
Manfred

Bootdata ok (command line is root=/dev/md0 ro )
Linux version 2.6.18-4-amd64 (Debian 2.6.18.dfsg.1-12) (waldi@debian.org) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #1 SMP Mon Mar 26 11:36:53 CEST 2007
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000007e790000 (usable)
BIOS-e820: 000000007e790000 - 000000007e79e000 (ACPI data)
BIOS-e820: 000000007e79e000 - 000000007e7e0000 (ACPI NVS)
BIOS-e820: 000000007e7e0000 - 000000007e800000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
DMI 2.4 present.
ACPI: RSDP (v000 ACPIAM ) @ 0x00000000000fad70
ACPI: RSDT (v001 NEC 0x03000719 MSFT 0x00000097) @ 0x000000007e790000
ACPI: FADT (v002 MSTEST OEMFACP 0x03000719 MSFT 0x00000097) @ 0x000000007e790200
ACPI: MADT (v001 MSTEST OEMAPIC 0x03000719 MSFT 0x00000097) @ 0x000000007e790390
ACPI: MCFG (v001 MSTEST OEMMCFG 0x03000719 MSFT 0x00000097) @ 0x000000007e790400
ACPI: SLIC (v001 NEC 0x03000719 MSFT 0x00000097) @ 0x000000007e790440
ACPI: OEMB (v001 MSTEST AMI_OEM 0x03000719 MSFT 0x00000097) @ 0x000000007e79e040
ACPI: HPET (v001 MSTEST OEMHPET 0x03000719 MSFT 0x00000097) @ 0x000000007e79a250
ACPI: ASF! (v032 LEGEND I865PASF 0x00000001 INTL 0x20060113) @ 0x000000007e79a288
ACPI: GSCI (v001 MSTEST GMCHSCI 0x03000719 MSFT 0x00000097) @ 0x000000007e79e0c0
ACPI: SSDT (v001 AMI CPU1PM 0x00000001 INTL 0x20060113) @ 0x000000007e7a00f0
ACPI: SSDT (v001 AMI CPU2PM 0x00000001 INTL 0x20060113) @ 0x000000007e7a02b0
ACPI: DSDT (v001 A0579 A0579000 0x00000000 INTL 0x20060113) @ 0x0000000000000000
No NUMA configuration found
Faking a node at 0000000000000000-000000007e790000
Bootmem setup node 0 0000000000000000-000000007e790000
On node 0 totalpages: 509966
DMA zone: 3056 pages, LIFO batch:0
DMA32 zone: 506910 pages, LIFO batch:31
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 6:15 APIC version 20
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1 6:15 APIC version 20
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled)
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Setting APIC routing to physical flat
ACPI: HPET id: 0x8086a202 base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 80000000 (gap: 7e800000:80600000)
SMP: Allowing 4 CPUs, 2 hotplug CPUs
Built 1 zonelists. Total pages: 509966
Kernel command line: root=/dev/md0 ro
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
time.c: Using 14.318180 MHz WALL HPET GTOD HPET/TSC timer.
time.c: Detected 1866.670 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
Checking aperture...
Memory: 2030880k/2072128k available (1930k kernel code, 40860k reserved, 868k data, 176k init)
Calibrating delay using timer specific routine.. 3736.72 BogoMIPS (lpj=7473459)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 256
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
using mwait in idle threads.
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU0: Thermal monitoring enabled (TM2)
SMP alternatives: switching to UP code
ACPI: Core revision 20060707
Using local APIC timer interrupts.
result 16666702
Detected 16.666 MHz APIC timer.
SMP alternatives: switching to SMP code
Booting processor 1/2 APIC 0x1
Initializing CPU#1
Calibrating delay using timer specific routine.. 3733.50 BogoMIPS (lpj=7467000)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU1: Thermal monitoring enabled (TM2)
Intel(R) Core(TM)2 CPU 6320 @ 1.86GHz stepping 06
Brought up 2 CPUs
testing NMI watchdog ... OK.
migration_cost=20
checking if image is initramfs... it is
Freeing initrd memory: 5661k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved
PCI: Not using MMCONFIG.
PCI: Using configuration type 1
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:00:02.0
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P8._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11 12 14 *15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 *14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs *3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 *7 10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: ACPI device : hid PNP0A08
pnp: ACPI device : hid PNP0C01
pnp: ACPI device : hid PNP0200
pnp: ACPI device : hid PNP0B00
pnp: ACPI device : hid PNP0800
pnp: ACPI device : hid PNP0C04
pnp: ACPI device : hid PNP0501
pnp: ACPI device : hid PNP0C02
pnp: ACPI device : hid PNP0C02
pnp: ACPI device : hid PNP0103
pnp: ACPI device : hid PNP0C02
pnp: ACPI device : hid PNP0303
pnp: ACPI device : hid PNP0C02
pnp: ACPI device : hid PNP0C01
pnp: PnP ACPI: found 14 devices
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
hpet0: at MMIO 0xfed00000 (virtual 0xffffffffff5fe000), IRQs 2, 8, 0
hpet0: 3 64-bit timers, 14318180 Hz
PCI-GART: No AMD northbridge found.
pnp: the driver 'system' has been registered
pnp: match found with the PnP device '00:01' and the driver 'system'
pnp: match found with the PnP device '00:07' and the driver 'system'
pnp: 00:07: ioport range 0x290-0x297 has been reserved
pnp: match found with the PnP device '00:08' and the driver 'system'
pnp: match found with the PnP device '00:0a' and the driver 'system'
pnp: match found with the PnP device '00:0c' and the driver 'system'
pnp: match found with the PnP device '00:0d' and the driver 'system'
PCI: Ignore bogus resource 6 [0:0] of 0000:00:02.0
PCI: Bridge: 0000:00:1c.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: bfe00000-bfefffff
PCI: Bridge: 0000:00:1c.4
IO window: a000-afff
MEM window: ff400000-ff4fffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1e.0
IO window: b000-bfff
MEM window: ff500000-ff5fffff
PREFETCH window: 80000000-800fffff
GSI 16 sharing vector 0xA9 and IRQ 16
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1c.0 to 64
ACPI: PCI Interrupt 0000:00:1c.4[A] -> GSI 17 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1c.4 to 64
PCI: Setting latency timer of device 0000:00:1e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
audit: initializing netlink socket (disabled)
audit(1183842440.080:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: Setting latency timer of device 0000:00:1c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.0cie00]
Allocate Port Service[0000:00:1c.0cie02]
PCI: Setting latency timer of device 0000:00:1c.4 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.4cie00]
Allocate Port Service[0000:00:1c.4cie02]
Real Time Clock Driver v1.12ac
hpet_resources: 0xfed00000 is busy
Linux agpgart interface v0.101 (c) Dave Jones
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
pnp: the driver 'serial' has been registered
pnp: match found with the PnP device '00:06' and the driver 'serial'
00:06: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
pnp: the driver 'i8042 kbd' has been registered
pnp: match found with the PnP device '00:0b' and the driver 'i8042 kbd'
pnp: the driver 'i8042 aux' has been registered
PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
PNP: PS/2 controller doesn't have AUX irq; using default 12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 8
NET: Registered protocol family 20
ACPI: (supports S0 S1 S3 S4 S5)
Freeing unused kernel memory: 176k freed
input: AT Translated Set 2 keyboard as /class/input/input0
ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI: Getting cpuindex for acpiid 0x3
ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI: Getting cpuindex for acpiid 0x4
USB Universal Host Controller Interface driver v3.0
GSI 17 sharing vector 0xC9 and IRQ 17
ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 16 (level, low) -> IRQ 201
PCI: Setting latency timer of device 0000:00:1a.0 to 64
uhci_hcd 0000:00:1a.0: UHCI Host Controller
uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1a.0: irq 201, io base 0x0000d880
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ieee1394: Initialized config rom entry `ip1394'
ACPI: PCI Interrupt 0000:00:1a.1[b] -> GSI 17 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1a.1 to 64
uhci_hcd 0000:00:1a.1: UHCI Host Controller
uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1a.1: irq 169, io base 0x0000dc00
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
GSI 18 sharing vector 0xD1 and IRQ 18
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 209
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.0: irq 209, io base 0x0000d400
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
GSI 19 sharing vector 0xD9 and IRQ 19
ACPI: PCI Interrupt 0000:00:1d.1[b] -> GSI 19 (level, low) -> IRQ 217
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.1: irq 217, io base 0x0000d480
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
GSI 20 sharing vector 0xE1 and IRQ 20
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 225
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.2: irq 225, io base 0x0000d800
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1a.7[C] -> GSI 18 (level, low) -> IRQ 225
PCI: Setting latency timer of device 0000:00:1a.7 to 64
ehci_hcd 0000:00:1a.7: EHCI Host Controller
ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 6
ehci_hcd 0000:00:1a.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1a.7
ehci_hcd 0000:00:1a.7: irq 225, io mem 0xff9fb800
ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb6: configuration #1 chosen from 1 choice
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 4 ports detected
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 209
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 7
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 209, io mem 0xff9fb400
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb7: configuration #1 chosen from 1 choice
hub 7-0:1.0: USB hub found
hub 7-0:1.0: 6 ports detected
JMB363: IDE controller at PCI slot 0000:01:00.1
PCI: Enabling device 0000:01:00.1 (0000 -> 0001)
ACPI: PCI Interrupt 0000:01:00.1[b] -> GSI 17 (level, low) -> IRQ 169
JMB363: chipset revision 3
JMB363: 100% native mode on irq 169
PCI: Setting latency timer of device 0000:01:00.1 to 64
ide2: BM-DMA at 0xa400-0xa407, BIOS settings: hdeio, hdfio
ide3: BM-DMA at 0xa408-0xa40f, BIOS settings: hdgio, hdhio
Probing IDE interface ide2...
usb 5-2: new low speed USB device using uhci_hcd and address 2
Probing IDE interface ide3...
usb 5-2: configuration #1 chosen from 1 choice
usbcore: registered new driver hiddev
input: Logitech USB-PS/2 Optical Mouse as /class/input/input1
input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:1d.2-2
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
GSI 21 sharing vector 0xE9 and IRQ 21
ACPI: PCI Interrupt 0000:03:03.0[A] -> GSI 21 (level, low) -> IRQ 233
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[233] MMIO=[ff5ff800-ff5fffff] Max Packet=[2048] IR/IT contexts=[4/8]
JMB361: IDE controller at PCI slot 0000:01:00.0
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 201
JMB361: chipset revision 3
JMB361: 100% native mode on irq 201
JMB361: dma_base is invalid
ide0: JMB361 Bus-Master DMA disabled (BIOS)
JMB361: dma_base is invalid
ide1: JMB361 Bus-Master DMA disabled (BIOS)
Probing IDE interface ide0...
SCSI subsystem initialized
libata version 2.00 loaded.
Probing IDE interface ide1...
ACPI: PCI Interrupt 0000:03:04.0[A] -> GSI 19 (level, low) -> IRQ 217
skge 1.6 addr 0xff5f8000 irq 217 chip Yukon-Lite rev 9
skge eth0: addr 00:1b:fc:7c:0a:bd
ata_piix 0000:00:1f.2: version 2.00
ata_piix 0000:00:1f.2: MAP [ P0 -- P1 -- ]
ACPI: PCI Interrupt 0000:00:1f.2[b] -> GSI 19 (level, low) -> IRQ 217
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ata1: SATA max UDMA/133 cmd 0xE880 ctl 0xE802 bmdma 0xE080 irq 217
ata2: SATA max UDMA/133 cmd 0xE480 ctl 0xE402 bmdma 0xE088 irq 217
scsi0 : ata_piix
ieee1394: Host added: ID:BUS[0-00:1023] GUID[0011d800015071d2]
ata1.00: ATA-7, max UDMA/133, 625142448 sectors: LBA48 NCQ (depth 0/32)
ata1.00: ata1: dev 0 multi count 16
ata1.00: configured for UDMA/133
scsi1 : ata_piix
ata2.00: ATA-7, max UDMA/133, 625142448 sectors: LBA48 NCQ (depth 0/32)
ata2.00: ata2: dev 0 multi count 16
ata2.00: configured for UDMA/133
Vendor: ATA Model: ST3320620AS Rev: 3.AA
Type: Direct-Access ANSI SCSI revision: 05
Vendor: ATA Model: ST3320620AS Rev: 3.AA
Type: Direct-Access ANSI SCSI revision: 05
ata_piix 0000:00:1f.5: MAP [ P0 -- P1 -- ]
ACPI: PCI Interrupt 0000:00:1f.5[b] -> GSI 19 (level, low) -> IRQ 217
PCI: Setting latency timer of device 0000:00:1f.5 to 64
ata3: SATA max UDMA/133 cmd 0xD080 ctl 0xD002 bmdma 0xC800 irq 217
ata4: SATA max UDMA/133 cmd 0xCC00 ctl 0xC882 bmdma 0xC808 irq 217
scsi2 : ata_piix
ata3.00: ATA-7, max UDMA/133, 625142448 sectors: LBA48 NCQ (depth 0/32)
ata3.00: ata3: dev 0 multi count 16
ata3.00: configured for UDMA/133
scsi3 : ata_piix
ATA: abnormal status 0x7F on port 0xCC07
Vendor: ATA Model: ST3320620AS Rev: 3.AA
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda3
sd 0:0:0:0: Attached scsi disk sda
SCSI device sdb: 625142448 512-byte hdwr sectors (320073 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: drive cache: write back
SCSI device sdb: 625142448 512-byte hdwr sectors (320073 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: drive cache: write back
sdb: sdb1 sdb2 sdb3
sd 1:0:0:0: Attached scsi disk sdb
SCSI device sdc: 625142448 512-byte hdwr sectors (320073 MB)
sdc: Write Protect is off
sdc: Mode Sense: 00 3a 00 00
SCSI device sdc: drive cache: write back
SCSI device sdc: 625142448 512-byte hdwr sectors (320073 MB)
sdc: Write Protect is off
sdc: Mode Sense: 00 3a 00 00
SCSI device sdc: drive cache: write back
sdc: sdc1 sdc2 sdc3
sd 2:0:0:0: Attached scsi disk sdc
Probing IDE interface ide0...
Probing IDE interface ide1...
Probing IDE interface ide2...
Probing IDE interface ide3...
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
md: raid1 personality registered for level 1
raid5: automatically using best checksumming function: generic_sse
generic_sse: 6839.000 MB/sec
raid5: using function: generic_sse (6839.000 MB/sec)
raid6: int64x1 1750 MB/s
raid6: int64x2 2111 MB/s
raid6: int64x4 2016 MB/s
raid6: int64x8 1342 MB/s
raid6: sse2x1 3208 MB/s
raid6: sse2x2 3834 MB/s
raid6: sse2x4 5546 MB/s
raid6: using algorithm sse2x4 (5546 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
md: md0 stopped.
md: bind<sdb1>
md: bind<sdc1>
md: bind<sda1>
raid1: raid set md0 active with 2 out of 2 mirrors
md: md1 stopped.
md: bind<sdb3>
md: bind<sdc3>
md: bind<sda3>
raid5: device sda3 operational as raid disk 0
raid5: device sdc3 operational as raid disk 2
raid5: device sdb3 operational as raid disk 1
raid5: allocated 3212kB for md1
raid5: raid level 5 set md1 active with 3 out of 3 devices, algorithm 2
RAID5 conf printout:
--- rd:3 wd:3 fd:0
disk 0, o:1, dev:sda3
disk 1, o:1, dev:sdb3
disk 2, o:1, dev:sdc3
device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: dm-devel@redhat.com
Attempting manual resume
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
ts: Compaq touchscreen protocol output
eth1394: eth0: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
input: PC Speaker as /class/input/input2
PCI: Enabling device 0000:00:1f.3 (0001 -> 0003)
ACPI: PCI Interrupt 0000:00:1f.3[C] -> GSI 18 (level, low) -> IRQ 225
GSI 22 sharing vector 0x32 and IRQ 22
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 50
PCI: Setting latency timer of device 0000:00:1b.0 to 64
hda_codec: Unknown model for AD1988, trying auto-probe from BIOS...
Adding 979956k swap on /dev/sda2. Priority:-1 extents:1 across:979956k
Adding 979956k swap on /dev/sdb2. Priority:-2 extents:1 across:979956k
Adding 979956k swap on /dev/sdc2. Priority:-3 extents:1 across:979956k
EXT3 FS on md0, internal journal
loop: loaded (max 8 devices)
ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1)
ieee1394: sbp2: Try serialize_io=0 for better performance
agpgart: Detected an Intel 965G Chipset.
agpgart: Detected 7676K stolen memory.
agpgart: AGP aperture is 512M @ 0xd0000000
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-0, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-4, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
skge eth1: enabling interface
skge eth1: Link is up at 100 Mbps, full duplex, flow control tx and rx
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
pnp: the driver 'parport_pc' has been registered
lp: driver loaded but no devices found
ppdev: user-space parallel port driver
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
[drm] Initialized drm 1.0.1 20051102
ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 201
[drm] Initialized i915 1.5.0 20060119 on minor 0
eth1: no IPv6 routers present

Linux version 2.6.19.5 (root@Knoppix) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #4 SMP PREEMPT Sat Mar 3 02:19:32 CET 2007
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000007e790000 (usable)
BIOS-e820: 000000007e790000 - 000000007e79e000 (ACPI data)
BIOS-e820: 000000007e79e000 - 000000007e7e0000 (ACPI NVS)
BIOS-e820: 000000007e7e0000 - 000000007e800000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
1127MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000ff780
Entering add_active_range(0, 0, 518032) 0 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 229376
HighMem 229376 -> 518032
early_node_map[1] active PFN ranges
0: 0 -> 518032
On node 0 totalpages: 518032
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 1760 pages used for memmap
Normal zone: 223520 pages, LIFO batch:31
HighMem zone: 2255 pages used for memmap
HighMem zone: 286401 pages, LIFO batch:31
DMI 2.4 present.
ACPI: RSDP (v000 ACPIAM ) @ 0x000fad70
ACPI: RSDT (v001 NEC 0x03000719 MSFT 0x00000097) @ 0x7e790000
ACPI: FADT (v002 MSTEST OEMFACP 0x03000719 MSFT 0x00000097) @ 0x7e790200
ACPI: MADT (v001 MSTEST OEMAPIC 0x03000719 MSFT 0x00000097) @ 0x7e790390
ACPI: MCFG (v001 MSTEST OEMMCFG 0x03000719 MSFT 0x00000097) @ 0x7e790400
ACPI: SLIC (v001 NEC 0x03000719 MSFT 0x00000097) @ 0x7e790440
ACPI: OEMB (v001 MSTEST AMI_OEM 0x03000719 MSFT 0x00000097) @ 0x7e79e040
ACPI: HPET (v001 MSTEST OEMHPET 0x03000719 MSFT 0x00000097) @ 0x7e79a250
ACPI: ASF! (v032 LEGEND I865PASF 0x00000001 INTL 0x20060113) @ 0x7e79a288
ACPI: GSCI (v001 MSTEST GMCHSCI 0x03000719 MSFT 0x00000097) @ 0x7e79e0c0
ACPI: SSDT (v001 AMI CPU1PM 0x00000001 INTL 0x20060113) @ 0x7e7a00f0
ACPI: SSDT (v001 AMI CPU2PM 0x00000001 INTL 0x20060113) @ 0x7e7a02b0
ACPI: DSDT (v001 A0579 A0579000 0x00000000 INTL 0x20060113) @ 0x00000000
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 6:15 APIC version 20
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1 6:15 APIC version 20
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled)
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
ACPI: HPET id: 0x8086a202 base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 80000000 (gap: 7e800000:80600000)
Detected 1866.736 MHz processor.
Built 1 zonelists. Total pages: 513985
Kernel command line: ramdisk_size=100000 init=/etc/init lang=de apm=power-off vga=791 initrd=minirt.gz nomce loglevel=0 libata.atapi_enabled=1 quiet nmi_watchdog=0 BOOT_IMAGE=knoppix BOOT_IMAGE=linux
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Console: colour dummy device 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 2048256k/2072128k available (2748k kernel code, 22668k reserved, 956k data, 336k init, 1154624k highmem)
virtual kernel memory layout:
fixmap : 0xffe16000 - 0xfffff000 (1956 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
.init : 0xc04a6000 - 0xc04fa000 ( 336 kB)
.data : 0xc03af3bc - 0xc049e7b4 ( 956 kB)
.text : 0xc0100000 - 0xc03af3bc (2748 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Using HPET for base-timer
Calibrating delay using timer specific routine.. 3736.14 BogoMIPS (lpj=7472281)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e3bd 00000000 00000001
monitor/mwait feature present.
using mwait in idle threads.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU: After all inits, caps: bfebfbff 20100000 00000000 00000940 0000e3bd 00000000 00000001
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
SMP alternatives: switching to UP code
ACPI: Core revision 20060707
CPU0: Intel(R) Core(TM)2 CPU 6320 @ 1.86GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 1/1 eip 3000
Initializing CPU#1
Calibrating delay using timer specific routine.. 3733.42 BogoMIPS (lpj=7466847)
CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e3bd 00000000 00000001
monitor/mwait feature present.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU: After all inits, caps: bfebfbff 20100000 00000000 00000940 0000e3bd 00000000 00000001
CPU1: Intel(R) Core(TM)2 CPU 6320 @ 1.86GHz stepping 06
Total of 2 processors activated (7469.56 BogoMIPS).
ENABLING IO-APIC IRQs
...TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
checking TSC synchronization across 2 CPUs: passed.
Brought up 2 CPUs
migration_cost=665
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 1189k freed
NET: Registered protocol family 16
EISA bus registered
ACPI: bus type pci registered
PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved
PCI: Not using MMCONFIG.
PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=3
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:00:02.0
PCI quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO
PCI quirk: region 0480-04bf claimed by ICH6 GPIO
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P8._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11 12 14 *15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 *14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs *3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 *7 10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 14 devices
PnPBIOS: Disabled by ACPI PNP
SCSI subsystem initialized
libata version 2.00 loaded.
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
pnp: 00:07: ioport range 0x290-0x297 has been reserved
PCI: Ignore bogus resource 6 [0:0] of 0000:00:02.0
PCI: Bridge: 0000:00:1c.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: bfe00000-bfefffff
PCI: Bridge: 0000:00:1c.4
IO window: a000-afff
MEM window: ff400000-ff4fffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1e.0
IO window: b000-bfff
MEM window: ff500000-ff5fffff
PREFETCH window: 80000000-800fffff
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1c.0 to 64
ACPI: PCI Interrupt 0000:00:1c.4[A] -> GSI 17 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1c.4 to 64
PCI: Setting latency timer of device 0000:00:1e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1572864 bytes)
TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
audit: initializing netlink socket (disabled)
audit(1183842679.792:1): initialized
highmem bounce pool size: 64 pages
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
fuse init (API version 7.8)
fuse distribution version: 2.6.1
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered (default)
io scheduler cfq registered
PCI: Setting latency timer of device 0000:00:1c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.0cie00]
Allocate Port Service[0000:00:1c.0cie02]
PCI: Setting latency timer of device 0000:00:1c.4 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.4cie00]
Allocate Port Service[0000:00:1c.4cie02]
vesafb: framebuffer at 0xd0000000, mapped to 0xf8880000, using 3072k, total 7616k
vesafb: mode is 1024x768x16, linelength=2048, pages=3
vesafb: protected mode interface info at 00ff:44f0
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
floppy0: no floppy controllers found
RAMDISK driver initialized: 16 RAM disks of 100000K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
JMB363: IDE controller at PCI slot 0000:01:00.1
PCI: Enabling device 0000:01:00.1 (0000 -> 0001)
ACPI: PCI Interrupt 0000:01:00.1[b] -> GSI 17 (level, low) -> IRQ 16
JMB363: chipset revision 3
JMB363: 100% native mode on irq 16
PCI: Setting latency timer of device 0000:01:00.1 to 64
ide2: BM-DMA at 0xa400-0xa407, BIOS settings: hdeio, hdfio
ide3: BM-DMA at 0xa408-0xa40f, BIOS settings: hdgMA, hdhMA
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide0...
Probing IDE interface ide1...
Probing IDE interface ide2...
Probing IDE interface ide3...
Loading iSCSI transport class v2.0-724.<7>ahci 0000:01:00.0: version 2.0
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:01:00.0 to 64
ahci 0000:01:00.0: AHCI 0001.0000 32 slots 2 ports 3 Gbps 0x3 impl SATA mode
ahci 0000:01:00.0: flags: 64bit ncq pm led clo pmp pio slum part
ata1: SATA max UDMA/133 cmd 0xF8828100 ctl 0x0 bmdma 0x0 irq 17
ata2: SATA max UDMA/133 cmd 0xF8828180 ctl 0x0 bmdma 0x0 irq 17
scsi0 : ahci
ata1: SATA link down (SStatus 0 SControl 300)
scsi1 : ahci
ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata2.00: ATAPI, max UDMA/100
ata2.00: configured for UDMA/100
scsi 1:0:0:0: CD-ROM HL-DT-ST DVDRAM GSA-H62N CL00 PQ: 0 ANSI: 5
ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
ata2.00: (irq_stat 0x48000000, interface fatal error)
ata2.00: tag 0 cmd 0xa0 Emask 0x50 stat 0x51 err 0x64 (ATA bus error)
ata2: soft resetting port
ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata2.00: configured for UDMA/100
ata2: EH complete
sr0: scsi3-mmc drive: 125x/125x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 1:0:0:0: Attached scsi CD-ROM sr0
ata_piix 0000:00:1f.2: version 2.00ac6
ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
ACPI: PCI Interrupt 0000:00:1f.2[b] -> GSI 19 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ata3: SATA max UDMA/133 cmd 0xE880 ctl 0xE802 bmdma 0xE080 irq 18
ata4: SATA max UDMA/133 cmd 0xE480 ctl 0xE402 bmdma 0xE088 irq 18
scsi2 : ata_piix
ata3.00: ATA-7, max UDMA/133, 625142448 sectors: LBA48 NCQ (depth 0/32)
ata3.00: ata3: dev 0 multi count 16
ata3.00: configured for UDMA/133
scsi3 : ata_piix
ata4.00: ATA-7, max UDMA/133, 625142448 sectors: LBA48 NCQ (depth 0/32)
ata4.00: ata4: dev 0 multi count 16
ata4.00: configured for UDMA/133
scsi 2:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5
SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda3
sd 2:0:0:0: Attached scsi disk sda
scsi 3:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5
SCSI device sdb: 625142448 512-byte hdwr sectors (320073 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: drive cache: write back
SCSI device sdb: 625142448 512-byte hdwr sectors (320073 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: drive cache: write back
sdb: sdb1 sdb2 sdb3
sd 3:0:0:0: Attached scsi disk sdb
ata_piix 0000:00:1f.5: MAP [ P0 P2 P1 P3 ]
ACPI: PCI Interrupt 0000:00:1f.5[b] -> GSI 19 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1f.5 to 64
ata5: SATA max UDMA/133 cmd 0xD080 ctl 0xD002 bmdma 0xC800 irq 18
ata6: SATA max UDMA/133 cmd 0xCC00 ctl 0xC882 bmdma 0xC808 irq 18
scsi4 : ata_piix
ata5.00: ATA-7, max UDMA/133, 625142448 sectors: LBA48 NCQ (depth 0/32)
ata5.00: ata5: dev 0 multi count 16
ata5.00: configured for UDMA/133
scsi5 : ata_piix
ATA: abnormal status 0x7F on port 0xCC07
scsi 4:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5
SCSI device sdc: 625142448 512-byte hdwr sectors (320073 MB)
sdc: Write Protect is off
sdc: Mode Sense: 00 3a 00 00
SCSI device sdc: drive cache: write back
SCSI device sdc: 625142448 512-byte hdwr sectors (320073 MB)
sdc: Write Protect is off
sdc: Mode Sense: 00 3a 00 00
SCSI device sdc: drive cache: write back
sdc: sdc1 sdc2 sdc3
sd 4:0:0:0: Attached scsi disk sdc
PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
PNP: PS/2 controller doesn't have AUX irq; using default 12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
EISA: Probing bus 0 at eisa.0
EISA: Detected 0 cards.
Initializing XFRM netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 15
Using IPI No-Shortcut mode
ACPI: (supports S0 S1 S3 S4 S5)
Time: tsc clocksource has been installed.
input: AT Translated Set 2 keyboard as /class/input/input0
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
Failed initialization of WD-7000 SCSI card!
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ACPI: PCI Interrupt 0000:00:1a.7[C] -> GSI 18 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1a.7 to 64
ehci_hcd 0000:00:1a.7: EHCI Host Controller
ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1a.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1a.7
ehci_hcd 0000:00:1a.7: irq 19, io mem 0xff9fb800
ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 20, io mem 0xff9fb400
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 6 ports detected
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 16 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1a.0 to 64
uhci_hcd 0000:00:1a.0: UHCI Host Controller
uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1a.0: irq 17, io base 0x0000d880
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1a.1[b] -> GSI 17 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1a.1 to 64
uhci_hcd 0000:00:1a.1: UHCI Host Controller
uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1a.1: irq 16, io base 0x0000dc00
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.0: irq 20, io base 0x0000d400
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[b] -> GSI 19 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 6
uhci_hcd 0000:00:1d.1: irq 18, io base 0x0000d480
usb usb6: configuration #1 chosen from 1 choice
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 7
uhci_hcd 0000:00:1d.2: irq 19, io base 0x0000d800
usb usb7: configuration #1 chosen from 1 choice
hub 7-0:1.0: USB hub found
hub 7-0:1.0: 2 ports detected
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
usb 7-2: new low speed USB device using uhci_hcd and address 2
usb 7-2: configuration #1 chosen from 1 choice
usbcore: registered new interface driver libusual
usbcore: registered new interface driver hiddev
input: Logitech USB-PS/2 Optical Mouse as /class/input/input1
input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:1d.2-2
usbcore: registered new interface driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
ieee1394: Initialized config rom entry `ip1394'
ACPI: PCI Interrupt 0000:03:03.0[A] -> GSI 21 (level, low) -> IRQ 21
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[21] MMIO=[ff5ff800-ff5fffff] Max Packet=[2048] IR/IT contexts=[4/8]
ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1)
ieee1394: sbp2: Try serialize_io=0 for better performance
ieee1394: Host added: ID:BUS[0-00:1023] GUID[0011d800015071d2]
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
cloop: Initializing cloop v2.06
cloop: loaded (max 8 devices)
cloop: /cdrom/KNOPPIX/KNOPPIX: 49667 blocks, 131072 bytes/block, largest block is 131118 bytes.
cloop: loaded 256 blocks into cache.
ISO 9660 Extensions: RRIP_1991A
cloop: losetup_file: 38179 blocks, 131072 bytes/block, largest block is 131118 bytes.
cloop: loaded 256 blocks into cache.
ISO 9660 Extensions: RRIP_1991A
aufs 20070226
Freeing unused kernel memory: 336k freed
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
Using specific hotkey driver
ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI: Getting cpuindex for acpiid 0x3
ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI: Getting cpuindex for acpiid 0x4
cpufreq: No nForce2 chipset.
p4-clockmod: Unknown p4-clockmod-capable CPU. Please send an e-mail to <linux@brodo.de>
p4-clockmod: Unknown p4-clockmod-capable CPU. Please send an e-mail to <linux@brodo.de>
powernow: This module only works with AMD K7 CPUs
ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
ata2.00: (irq_stat 0x48000000, interface fatal error)
ata2.00: tag 0 cmd 0xa0 Emask 0x50 stat 0x51 err 0x54 (ATA bus error)
ata2: soft resetting port
ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata2.00: configured for UDMA/100
ata2: EH complete
eth1394: eth0: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
ata2.00: (irq_stat 0x48000000, interface fatal error)
ata2.00: tag 0 cmd 0xa0 Emask 0x50 stat 0x51 err 0x54 (ATA bus error)
sr 1:0:0:0: Attached scsi generic sg0 type 5
sd 2:0:0:0: Attached scsi generic sg1 type 0
sd 3:0:0:0: Attached scsi generic sg2 type 0
sd 4:0:0:0: Attached scsi generic sg3 type 0
ata2: soft resetting port
ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata2.00: configured for UDMA/100
ata2: EH complete
PCI: Enabling device 0000:00:1f.3 (0001 -> 0003)
ACPI: PCI Interrupt 0000:00:1f.3[C] -> GSI 18 (level, low) -> IRQ 19
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel 965G Chipset.
agpgart: Detected 7676K stolen memory.
agpgart: AGP aperture is 512M @ 0xd0000000
ACPI: PCI Interrupt 0000:03:04.0[A] -> GSI 19 (level, low) -> IRQ 18
skge 1.9 addr 0xff5f8000 irq 18 chip Yukon-Lite rev 9
skge eth1: addr 00:1b:fc:7c:0a:bd
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:06: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 22
PCI: Setting latency timer of device 0000:00:1b.0 to 64
hda_codec: Unknown model for AD1988, trying auto-probe from BIOS...
device-mapper: ioctl: 4.10.0-ioctl (2006-09-14) initialised: dm-devel@redhat.com
Adding 979956k swap on /dev/sda2. Priority:-1 extents:1 across:979956k
Adding 979956k swap on /dev/sdb2. Priority:-2 extents:1 across:979956k
Adding 979956k swap on /dev/sdc2. Priority:-3 extents:1 across:979956k
NET: Registered protocol family 17
skge eth1: enabling interface
skge eth1: Link is up at 100 Mbps, full duplex, flow control both
[drm] Initialized drm 1.0.1 20051102
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
Mobile IPv6
ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 17
[drm] Initialized i915 1.5.0 20060119 on minor 0
eth1: no IPv6 routers present
skge eth1: disabling interface
skge eth1: enabling interface
skge eth1: Link is up at 100 Mbps, full duplex, flow control both
eth1: no IPv6 routers present

<attachement...>
> scsi 1:0:0:0: CD-ROM HL-DT-ST DVDRAM GSA-H62N CL00 PQ: 0
ANSI: 5
> ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
> ata2.00: (irq_stat 0x48000000, interface fatal error)
> ata2.00: tag 0 cmd 0xa0 Emask 0x50 stat 0x51 err 0x64 (ATA bus error)
> ata2: soft resetting port
> ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
> ata2.00: configured for UDMA/100
> ata2: EH complete
> sr0: scsi3-mmc drive: 125x/125x writer dvd-ram cd/rw xa/form2 cdda tray
> Uniform CD-ROM driver Revision: 3.20
> sr 1:0:0:0: Attached scsi CD-ROM sr0
> ata_piix 0000:00:1f.2: version 2.00ac6
> ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
> ACPI: PCI Interrupt 0000:00:1f.2[b] -> GSI 19 (level, low) -> IRQ 18

Looks like a dvd rw drive WAS detected at ata2.00 assigned to sr0


anfred Lutz wrote:
> Hi all!
>
> few days ago I installed Etch on my computer and am now stuck with the
> DVD writer. The installer had no issue booting from the drive and do the
> installation. But the installed system no longer detects that a DVD
> drive is there.
>
> The DVD is a SATA drive from LG, connected to a JMicron SATA/IDE JMB 363
> (according mainboard manual) controller. I'm wondering that the Etch
> installer was able to run this combination, whereas the Etch
> installation does not...
>
> Searching the net about that issue I'm even more wondering that the
> installation worked, after I read that support for the JMicron
> controller was introduced with 2.6.19. Don't get me wrong, I'm not
> complaining that the installation worked that smoothly... :-)
>
> Booting Knoppix 5.2 live CD works well, with the DVD being fine... but
> that's based on 2.6.19 anyway...
>
> Changing BIOS settings for the JMicron controller from IDE to AHCI
> didn't made a difference.
>
> Has anyone seen this before and ideas how to get Etch detect my DVD drive?
>
> Thanks & best regards,
> Manfred
>
>
> ------------------------------------------------------------------------
>
> Bootdata ok (command line is root=/dev/md0 ro )
> Linux version 2.6.18-4-amd64 (Debian 2.6.18.dfsg.1-12) (waldi@debian.org) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #1 SMP Mon Mar 26 11:36:53 CEST 2007
> BIOS-provided physical RAM map:
> BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
> BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
> BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
> BIOS-e820: 0000000000100000 - 000000007e790000 (usable)
> BIOS-e820: 000000007e790000 - 000000007e79e000 (ACPI data)
> BIOS-e820: 000000007e79e000 - 000000007e7e0000 (ACPI NVS)
> BIOS-e820: 000000007e7e0000 - 000000007e800000 (reserved)
> BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
> BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
> DMI 2.4 present.
> ACPI: RSDP (v000 ACPIAM ) @ 0x00000000000fad70
> ACPI: RSDT (v001 NEC 0x03000719 MSFT 0x00000097) @ 0x000000007e790000
> ACPI: FADT (v002 MSTEST OEMFACP 0x03000719 MSFT 0x00000097) @ 0x000000007e790200
> ACPI: MADT (v001 MSTEST OEMAPIC 0x03000719 MSFT 0x00000097) @ 0x000000007e790390
> ACPI: MCFG (v001 MSTEST OEMMCFG 0x03000719 MSFT 0x00000097) @ 0x000000007e790400
> ACPI: SLIC (v001 NEC 0x03000719 MSFT 0x00000097) @ 0x000000007e790440
> ACPI: OEMB (v001 MSTEST AMI_OEM 0x03000719 MSFT 0x00000097) @ 0x000000007e79e040
> ACPI: HPET (v001 MSTEST OEMHPET 0x03000719 MSFT 0x00000097) @ 0x000000007e79a250
> ACPI: ASF! (v032 LEGEND I865PASF 0x00000001 INTL 0x20060113) @ 0x000000007e79a288
> ACPI: GSCI (v001 MSTEST GMCHSCI 0x03000719 MSFT 0x00000097) @ 0x000000007e79e0c0
> ACPI: SSDT (v001 AMI CPU1PM 0x00000001 INTL 0x20060113) @ 0x000000007e7a00f0
> ACPI: SSDT (v001 AMI CPU2PM 0x00000001 INTL 0x20060113) @ 0x000000007e7a02b0
> ACPI: DSDT (v001 A0579 A0579000 0x00000000 INTL 0x20060113) @ 0x0000000000000000
> No NUMA configuration found
> Faking a node at 0000000000000000-000000007e790000
> Bootmem setup node 0 0000000000000000-000000007e790000
> On node 0 totalpages: 509966
> DMA zone: 3056 pages, LIFO batch:0
> DMA32 zone: 506910 pages, LIFO batch:31
> ACPI: PM-Timer IO Port: 0x808
> ACPI: Local APIC address 0xfee00000
> ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
> Processor #0 6:15 APIC version 20
> ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
> Processor #1 6:15 APIC version 20
> ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled)
> ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled)
> ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
> IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
> ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
> ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
> ACPI: IRQ0 used by override.
> ACPI: IRQ2 used by override.
> ACPI: IRQ9 used by override.
> Setting APIC routing to physical flat
> ACPI: HPET id: 0x8086a202 base: 0xfed00000
> Using ACPI (MADT) for SMP configuration information
> Allocating PCI resources starting at 80000000 (gap: 7e800000:80600000)
> SMP: Allowing 4 CPUs, 2 hotplug CPUs
> Built 1 zonelists. Total pages: 509966
> Kernel command line: root=/dev/md0 ro
> Initializing CPU#0
> PID hash table entries: 4096 (order: 12, 32768 bytes)
> time.c: Using 14.318180 MHz WALL HPET GTOD HPET/TSC timer.
> time.c: Detected 1866.670 MHz processor.
> Console: colour VGA+ 80x25
> Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
> Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
> Checking aperture...
> Memory: 2030880k/2072128k available (1930k kernel code, 40860k reserved, 868k data, 176k init)
> Calibrating delay using timer specific routine.. 3736.72 BogoMIPS (lpj=7473459)
> Security Framework v1.0.0 initialized
> SELinux: Disabled at boot.
> Capability LSM initialized
> Mount-cache hash table entries: 256
> CPU: L1 I cache: 32K, L1 D cache: 32K
> CPU: L2 cache: 4096K
> using mwait in idle threads.
> CPU: Physical Processor ID: 0
> CPU: Processor Core ID: 0
> CPU0: Thermal monitoring enabled (TM2)
> SMP alternatives: switching to UP code
> ACPI: Core revision 20060707
> Using local APIC timer interrupts.
> result 16666702
> Detected 16.666 MHz APIC timer.
> SMP alternatives: switching to SMP code
> Booting processor 1/2 APIC 0x1
> Initializing CPU#1
> Calibrating delay using timer specific routine.. 3733.50 BogoMIPS (lpj=7467000)
> CPU: L1 I cache: 32K, L1 D cache: 32K
> CPU: L2 cache: 4096K
> CPU: Physical Processor ID: 0
> CPU: Processor Core ID: 1
> CPU1: Thermal monitoring enabled (TM2)
> Intel(R) Core(TM)2 CPU 6320 @ 1.86GHz stepping 06
> Brought up 2 CPUs
> testing NMI watchdog ... OK.
> migration_cost=20
> checking if image is initramfs... it is
> Freeing initrd memory: 5661k freed
> NET: Registered protocol family 16
> ACPI: bus type pci registered
> PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved
> PCI: Not using MMCONFIG.
> PCI: Using configuration type 1
> ACPI: Interpreter enabled
> ACPI: Using IOAPIC for interrupt routing
> ACPI: PCI Root Bridge [PCI0] (0000:00)
> PCI: Probing PCI hardware (bus 00)
> Boot video device is 0000:00:02.0
> PCI: Transparent bridge - 0000:00:1e.0
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P8._PRT]
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
> ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12 14 15)
> ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11 12 14 15)
> ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
> ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11 12 14 *15)
> ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
> ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 *14 15)
> ACPI: PCI Interrupt Link [LNKG] (IRQs *3 4 5 6 7 10 11 12 14 15)
> ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 *7 10 11 12 14 15)
> Linux Plug and Play Support v0.97 (c) Adam Belay
> pnp: PnP ACPI init
> pnp: ACPI device : hid PNP0A08
> pnp: ACPI device : hid PNP0C01
> pnp: ACPI device : hid PNP0200
> pnp: ACPI device : hid PNP0B00
> pnp: ACPI device : hid PNP0800
> pnp: ACPI device : hid PNP0C04
> pnp: ACPI device : hid PNP0501
> pnp: ACPI device : hid PNP0C02
> pnp: ACPI device : hid PNP0C02
> pnp: ACPI device : hid PNP0103
> pnp: ACPI device : hid PNP0C02
> pnp: ACPI device : hid PNP0303
> pnp: ACPI device : hid PNP0C02
> pnp: ACPI device : hid PNP0C01
> pnp: PnP ACPI: found 14 devices
> usbcore: registered new driver usbfs
> usbcore: registered new driver hub
> PCI: Using ACPI for IRQ routing
> PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
> hpet0: at MMIO 0xfed00000 (virtual 0xffffffffff5fe000), IRQs 2, 8, 0
> hpet0: 3 64-bit timers, 14318180 Hz
> PCI-GART: No AMD northbridge found.
> pnp: the driver 'system' has been registered
> pnp: match found with the PnP device '00:01' and the driver 'system'
> pnp: match found with the PnP device '00:07' and the driver 'system'
> pnp: 00:07: ioport range 0x290-0x297 has been reserved
> pnp: match found with the PnP device '00:08' and the driver 'system'
> pnp: match found with the PnP device '00:0a' and the driver 'system'
> pnp: match found with the PnP device '00:0c' and the driver 'system'
> pnp: match found with the PnP device '00:0d' and the driver 'system'
> PCI: Ignore bogus resource 6 [0:0] of 0000:00:02.0
> PCI: Bridge: 0000:00:1c.0
> IO window: disabled.
> MEM window: disabled.
> PREFETCH window: bfe00000-bfefffff
> PCI: Bridge: 0000:00:1c.4
> IO window: a000-afff
> MEM window: ff400000-ff4fffff
> PREFETCH window: disabled.
> PCI: Bridge: 0000:00:1e.0
> IO window: b000-bfff
> MEM window: ff500000-ff5fffff
> PREFETCH window: 80000000-800fffff
> GSI 16 sharing vector 0xA9 and IRQ 16
> ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 169
> PCI: Setting latency timer of device 0000:00:1c.0 to 64
> ACPI: PCI Interrupt 0000:00:1c.4[A] -> GSI 17 (level, low) -> IRQ 169
> PCI: Setting latency timer of device 0000:00:1c.4 to 64
> PCI: Setting latency timer of device 0000:00:1e.0 to 64
> NET: Registered protocol family 2
> IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
> TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
> TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
> TCP: Hash tables configured (established 262144 bind 65536)
> TCP reno registered
> audit: initializing netlink socket (disabled)
> audit(1183842440.080:1): initialized
> VFS: Disk quotas dquot_6.5.1
> Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
> Initializing Cryptographic API
> io scheduler noop registered
> io scheduler anticipatory registered
> io scheduler deadline registered
> io scheduler cfq registered (default)
> PCI: Setting latency timer of device 0000:00:1c.0 to 64
> assign_interrupt_mode Found MSI capability
> Allocate Port Service[0000:00:1c.0cie00]
> Allocate Port Service[0000:00:1c.0cie02]
> PCI: Setting latency timer of device 0000:00:1c.4 to 64
> assign_interrupt_mode Found MSI capability
> Allocate Port Service[0000:00:1c.4cie00]
> Allocate Port Service[0000:00:1c.4cie02]
> Real Time Clock Driver v1.12ac
> hpet_resources: 0xfed00000 is busy
> Linux agpgart interface v0.101 (c) Dave Jones
> Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
> serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
> pnp: the driver 'serial' has been registered
> pnp: match found with the PnP device '00:06' and the driver 'serial'
> 00:06: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
> RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
> pnp: the driver 'i8042 kbd' has been registered
> pnp: match found with the PnP device '00:0b' and the driver 'i8042 kbd'
> pnp: the driver 'i8042 aux' has been registered
> PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
> PNP: PS/2 controller doesn't have AUX irq; using default 12
> serio: i8042 AUX port at 0x60,0x64 irq 12
> serio: i8042 KBD port at 0x60,0x64 irq 1
> mice: PS/2 mouse device common for all mice
> TCP bic registered
> NET: Registered protocol family 1
> NET: Registered protocol family 17
> NET: Registered protocol family 8
> NET: Registered protocol family 20
> ACPI: (supports S0 S1 S3 S4 S5)
> Freeing unused kernel memory: 176k freed
> input: AT Translated Set 2 keyboard as /class/input/input0
> ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not present [20060707]
> ACPI: Getting cpuindex for acpiid 0x3
> ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not present [20060707]
> ACPI: Getting cpuindex for acpiid 0x4
> USB Universal Host Controller Interface driver v3.0
> GSI 17 sharing vector 0xC9 and IRQ 17
> ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 16 (level, low) -> IRQ 201
> PCI: Setting latency timer of device 0000:00:1a.0 to 64
> uhci_hcd 0000:00:1a.0: UHCI Host Controller
> uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1
> uhci_hcd 0000:00:1a.0: irq 201, io base 0x0000d880
> usb usb1: configuration #1 chosen from 1 choice
> hub 1-0:1.0: USB hub found
> hub 1-0:1.0: 2 ports detected
> Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
> ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
> ieee1394: Initialized config rom entry `ip1394'
> ACPI: PCI Interrupt 0000:00:1a.1[b] -> GSI 17 (level, low) -> IRQ 169
> PCI: Setting latency timer of device 0000:00:1a.1 to 64
> uhci_hcd 0000:00:1a.1: UHCI Host Controller
> uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 2
> uhci_hcd 0000:00:1a.1: irq 169, io base 0x0000dc00
> usb usb2: configuration #1 chosen from 1 choice
> hub 2-0:1.0: USB hub found
> hub 2-0:1.0: 2 ports detected
> GSI 18 sharing vector 0xD1 and IRQ 18
> ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 209
> PCI: Setting latency timer of device 0000:00:1d.0 to 64
> uhci_hcd 0000:00:1d.0: UHCI Host Controller
> uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 3
> uhci_hcd 0000:00:1d.0: irq 209, io base 0x0000d400
> usb usb3: configuration #1 chosen from 1 choice
> hub 3-0:1.0: USB hub found
> hub 3-0:1.0: 2 ports detected
> GSI 19 sharing vector 0xD9 and IRQ 19
> ACPI: PCI Interrupt 0000:00:1d.1[b] -> GSI 19 (level, low) -> IRQ 217
> PCI: Setting latency timer of device 0000:00:1d.1 to 64
> uhci_hcd 0000:00:1d.1: UHCI Host Controller
> uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 4
> uhci_hcd 0000:00:1d.1: irq 217, io base 0x0000d480
> usb usb4: configuration #1 chosen from 1 choice
> hub 4-0:1.0: USB hub found
> hub 4-0:1.0: 2 ports detected
> GSI 20 sharing vector 0xE1 and IRQ 20
> ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 225
> PCI: Setting latency timer of device 0000:00:1d.2 to 64
> uhci_hcd 0000:00:1d.2: UHCI Host Controller
> uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 5
> uhci_hcd 0000:00:1d.2: irq 225, io base 0x0000d800
> usb usb5: configuration #1 chosen from 1 choice
> hub 5-0:1.0: USB hub found
> hub 5-0:1.0: 2 ports detected
> ACPI: PCI Interrupt 0000:00:1a.7[C] -> GSI 18 (level, low) -> IRQ 225
> PCI: Setting latency timer of device 0000:00:1a.7 to 64
> ehci_hcd 0000:00:1a.7: EHCI Host Controller
> ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 6
> ehci_hcd 0000:00:1a.7: debug port 1
> PCI: cache line size of 32 is not supported by device 0000:00:1a.7
> ehci_hcd 0000:00:1a.7: irq 225, io mem 0xff9fb800
> ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
> usb usb6: configuration #1 chosen from 1 choice
> hub 6-0:1.0: USB hub found
> hub 6-0:1.0: 4 ports detected
> ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 209
> PCI: Setting latency timer of device 0000:00:1d.7 to 64
> ehci_hcd 0000:00:1d.7: EHCI Host Controller
> ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 7
> ehci_hcd 0000:00:1d.7: debug port 1
> PCI: cache line size of 32 is not supported by device 0000:00:1d.7
> ehci_hcd 0000:00:1d.7: irq 209, io mem 0xff9fb400
> ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
> usb usb7: configuration #1 chosen from 1 choice
> hub 7-0:1.0: USB hub found
> hub 7-0:1.0: 6 ports detected
> JMB363: IDE controller at PCI slot 0000:01:00.1
> PCI: Enabling device 0000:01:00.1 (0000 -> 0001)
> ACPI: PCI Interrupt 0000:01:00.1[b] -> GSI 17 (level, low) -> IRQ 169
> JMB363: chipset revision 3
> JMB363: 100% native mode on irq 169
> PCI: Setting latency timer of device 0000:01:00.1 to 64
> ide2: BM-DMA at 0xa400-0xa407, BIOS settings: hdeio, hdfio
> ide3: BM-DMA at 0xa408-0xa40f, BIOS settings: hdgio, hdhio
> Probing IDE interface ide2...
> usb 5-2: new low speed USB device using uhci_hcd and address 2
> Probing IDE interface ide3...
> usb 5-2: configuration #1 chosen from 1 choice
> usbcore: registered new driver hiddev
> input: Logitech USB-PS/2 Optical Mouse as /class/input/input1
> input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:1d.2-2
> usbcore: registered new driver usbhid
> drivers/usb/input/hid-core.c: v2.6:USB HID core driver
> GSI 21 sharing vector 0xE9 and IRQ 21
> ACPI: PCI Interrupt 0000:03:03.0[A] -> GSI 21 (level, low) -> IRQ 233
> ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[233] MMIO=[ff5ff800-ff5fffff] Max Packet=[2048] IR/IT contexts=[4/8]
> JMB361: IDE controller at PCI slot 0000:01:00.0
> ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 201
> JMB361: chipset revision 3
> JMB361: 100% native mode on irq 201
> JMB361: dma_base is invalid
> ide0: JMB361 Bus-Master DMA disabled (BIOS)
> JMB361: dma_base is invalid
> ide1: JMB361 Bus-Master DMA disabled (BIOS)
> Probing IDE interface ide0...
> SCSI subsystem initialized
> libata version 2.00 loaded.
> Probing IDE interface ide1...
> ACPI: PCI Interrupt 0000:03:04.0[A] -> GSI 19 (level, low) -> IRQ 217
> skge 1.6 addr 0xff5f8000 irq 217 chip Yukon-Lite rev 9
> skge eth0: addr 00:1b:fc:7c:0a:bd
> ata_piix 0000:00:1f.2: version 2.00
> ata_piix 0000:00:1f.2: MAP [ P0 -- P1 -- ]
> ACPI: PCI Interrupt 0000:00:1f.2[b] -> GSI 19 (level, low) -> IRQ 217
> PCI: Setting latency timer of device 0000:00:1f.2 to 64
> ata1: SATA max UDMA/133 cmd 0xE880 ctl 0xE802 bmdma 0xE080 irq 217
> ata2: SATA max UDMA/133 cmd 0xE480 ctl 0xE402 bmdma 0xE088 irq 217
> scsi0 : ata_piix
> ieee1394: Host added: ID:BUS[0-00:1023] GUID[0011d800015071d2]
> ata1.00: ATA-7, max UDMA/133, 625142448 sectors: LBA48 NCQ (depth 0/32)
> ata1.00: ata1: dev 0 multi count 16
> ata1.00: configured for UDMA/133
> scsi1 : ata_piix
> ata2.00: ATA-7, max UDMA/133, 625142448 sectors: LBA48 NCQ (depth 0/32)
> ata2.00: ata2: dev 0 multi count 16
> ata2.00: configured for UDMA/133
> Vendor: ATA Model: ST3320620AS Rev: 3.AA
> Type: Direct-Access ANSI SCSI revision: 05
> Vendor: ATA Model: ST3320620AS Rev: 3.AA
> Type: Direct-Access ANSI SCSI revision: 05
> ata_piix 0000:00:1f.5: MAP [ P0 -- P1 -- ]
> ACPI: PCI Interrupt 0000:00:1f.5[b] -> GSI 19 (level, low) -> IRQ 217
> PCI: Setting latency timer of device 0000:00:1f.5 to 64
> ata3: SATA max UDMA/133 cmd 0xD080 ctl 0xD002 bmdma 0xC800 irq 217
> ata4: SATA max UDMA/133 cmd 0xCC00 ctl 0xC882 bmdma 0xC808 irq 217
> scsi2 : ata_piix
> ata3.00: ATA-7, max UDMA/133, 625142448 sectors: LBA48 NCQ (depth 0/32)
> ata3.00: ata3: dev 0 multi count 16
> ata3.00: configured for UDMA/133
> scsi3 : ata_piix
> ATA: abnormal status 0x7F on port 0xCC07
> Vendor: ATA Model: ST3320620AS Rev: 3.AA
> Type: Direct-Access ANSI SCSI revision: 05
> SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
> sda: Write Protect is off
> sda: Mode Sense: 00 3a 00 00
> SCSI device sda: drive cache: write back
> SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
> sda: Write Protect is off
> sda: Mode Sense: 00 3a 00 00
> SCSI device sda: drive cache: write back
> sda: sda1 sda2 sda3
> sd 0:0:0:0: Attached scsi disk sda
> SCSI device sdb: 625142448 512-byte hdwr sectors (320073 MB)
> sdb: Write Protect is off
> sdb: Mode Sense: 00 3a 00 00
> SCSI device sdb: drive cache: write back
> SCSI device sdb: 625142448 512-byte hdwr sectors (320073 MB)
> sdb: Write Protect is off
> sdb: Mode Sense: 00 3a 00 00
> SCSI device sdb: drive cache: write back
> sdb: sdb1 sdb2 sdb3
> sd 1:0:0:0: Attached scsi disk sdb
> SCSI device sdc: 625142448 512-byte hdwr sectors (320073 MB)
> sdc: Write Protect is off
> sdc: Mode Sense: 00 3a 00 00
> SCSI device sdc: drive cache: write back
> SCSI device sdc: 625142448 512-byte hdwr sectors (320073 MB)
> sdc: Write Protect is off
> sdc: Mode Sense: 00 3a 00 00
> SCSI device sdc: drive cache: write back
> sdc: sdc1 sdc2 sdc3
> sd 2:0:0:0: Attached scsi disk sdc
> Probing IDE interface ide0...
> Probing IDE interface ide1...
> Probing IDE interface ide2...
> Probing IDE interface ide3...
> md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
> md: bitmap version 4.39
> md: raid1 personality registered for level 1
> raid5: automatically using best checksumming function: generic_sse
> generic_sse: 6839.000 MB/sec
> raid5: using function: generic_sse (6839.000 MB/sec)
> raid6: int64x1 1750 MB/s
> raid6: int64x2 2111 MB/s
> raid6: int64x4 2016 MB/s
> raid6: int64x8 1342 MB/s
> raid6: sse2x1 3208 MB/s
> raid6: sse2x2 3834 MB/s
> raid6: sse2x4 5546 MB/s
> raid6: using algorithm sse2x4 (5546 MB/s)
> md: raid6 personality registered for level 6
> md: raid5 personality registered for level 5
> md: raid4 personality registered for level 4
> md: md0 stopped.
> md: bind<sdb1>
> md: bind<sdc1>
> md: bind<sda1>
> raid1: raid set md0 active with 2 out of 2 mirrors
> md: md1 stopped.
> md: bind<sdb3>
> md: bind<sdc3>
> md: bind<sda3>
> raid5: device sda3 operational as raid disk 0
> raid5: device sdc3 operational as raid disk 2
> raid5: device sdb3 operational as raid disk 1
> raid5: allocated 3212kB for md1
> raid5: raid level 5 set md1 active with 3 out of 3 devices, algorithm 2
> RAID5 conf printout:
> --- rd:3 wd:3 fd:0
> disk 0, o:1, dev:sda3
> disk 1, o:1, dev:sdb3
> disk 2, o:1, dev:sdc3
> device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: dm-devel@redhat.com
> Attempting manual resume
> kjournald starting. Commit interval 5 seconds
> EXT3-fs: mounted filesystem with ordered data mode.
> ts: Compaq touchscreen protocol output
> eth1394: eth0: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
> input: PC Speaker as /class/input/input2
> PCI: Enabling device 0000:00:1f.3 (0001 -> 0003)
> ACPI: PCI Interrupt 0000:00:1f.3[C] -> GSI 18 (level, low) -> IRQ 225
> GSI 22 sharing vector 0x32 and IRQ 22
> ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 50
> PCI: Setting latency timer of device 0000:00:1b.0 to 64
> hda_codec: Unknown model for AD1988, trying auto-probe from BIOS...
> Adding 979956k swap on /dev/sda2. Priority:-1 extents:1 across:979956k
> Adding 979956k swap on /dev/sdb2. Priority:-2 extents:1 across:979956k
> Adding 979956k swap on /dev/sdc2. Priority:-3 extents:1 across:979956k
> EXT3 FS on md0, internal journal
> loop: loaded (max 8 devices)
> ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1)
> ieee1394: sbp2: Try serialize_io=0 for better performance
> agpgart: Detected an Intel 965G Chipset.
> agpgart: Detected 7676K stolen memory.
> agpgart: AGP aperture is 512M @ 0xd0000000
> kjournald starting. Commit interval 5 seconds
> EXT3 FS on dm-0, internal journal
> EXT3-fs: mounted filesystem with ordered data mode.
> kjournald starting. Commit interval 5 seconds
> EXT3 FS on dm-1, internal journal
> EXT3-fs: mounted filesystem with ordered data mode.
> kjournald starting. Commit interval 5 seconds
> EXT3 FS on dm-4, internal journal
> EXT3-fs: mounted filesystem with ordered data mode.
> kjournald starting. Commit interval 5 seconds
> EXT3 FS on dm-5, internal journal
> EXT3-fs: mounted filesystem with ordered data mode.
> kjournald starting. Commit interval 5 seconds
> EXT3 FS on dm-2, internal journal
> EXT3-fs: mounted filesystem with ordered data mode.
> kjournald starting. Commit interval 5 seconds
> EXT3 FS on dm-3, internal journal
> EXT3-fs: mounted filesystem with ordered data mode.
> skge eth1: enabling interface
> skge eth1: Link is up at 100 Mbps, full duplex, flow control tx and rx
> ACPI: Power Button (FF) [PWRF]
> ACPI: Power Button (CM) [PWRB]
> pnp: the driver 'parport_pc' has been registered
> lp: driver loaded but no devices found
> ppdev: user-space parallel port driver
> NET: Registered protocol family 10
> lo: Disabled Privacy Extensions
> IPv6 over IPv4 tunneling driver
> [drm] Initialized drm 1.0.1 20051102
> ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 201
> [drm] Initialized i915 1.5.0 20060119 on minor 0
> eth1: no IPv6 routers present
>
>
> ------------------------------------------------------------------------
>
> Linux version 2.6.19.5 (root@Knoppix) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #4 SMP PREEMPT Sat Mar 3 02:19:32 CET 2007
> BIOS-provided physical RAM map:
> BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
> BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
> BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
> BIOS-e820: 0000000000100000 - 000000007e790000 (usable)
> BIOS-e820: 000000007e790000 - 000000007e79e000 (ACPI data)
> BIOS-e820: 000000007e79e000 - 000000007e7e0000 (ACPI NVS)
> BIOS-e820: 000000007e7e0000 - 000000007e800000 (reserved)
> BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
> BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
> 1127MB HIGHMEM available.
> 896MB LOWMEM available.
> found SMP MP-table at 000ff780
> Entering add_active_range(0, 0, 518032) 0 entries of 256 used
> Zone PFN ranges:
> DMA 0 -> 4096
> Normal 4096 -> 229376
> HighMem 229376 -> 518032
> early_node_map[1] active PFN ranges
> 0: 0 -> 518032
> On node 0 totalpages: 518032
> DMA zone: 32 pages used for memmap
> DMA zone: 0 pages reserved
> DMA zone: 4064 pages, LIFO batch:0
> Normal zone: 1760 pages used for memmap
> Normal zone: 223520 pages, LIFO batch:31
> HighMem zone: 2255 pages used for memmap
> HighMem zone: 286401 pages, LIFO batch:31
> DMI 2.4 present.
> ACPI: RSDP (v000 ACPIAM ) @ 0x000fad70
> ACPI: RSDT (v001 NEC 0x03000719 MSFT 0x00000097) @ 0x7e790000
> ACPI: FADT (v002 MSTEST OEMFACP 0x03000719 MSFT 0x00000097) @ 0x7e790200
> ACPI: MADT (v001 MSTEST OEMAPIC 0x03000719 MSFT 0x00000097) @ 0x7e790390
> ACPI: MCFG (v001 MSTEST OEMMCFG 0x03000719 MSFT 0x00000097) @ 0x7e790400
> ACPI: SLIC (v001 NEC 0x03000719 MSFT 0x00000097) @ 0x7e790440
> ACPI: OEMB (v001 MSTEST AMI_OEM 0x03000719 MSFT 0x00000097) @ 0x7e79e040
> ACPI: HPET (v001 MSTEST OEMHPET 0x03000719 MSFT 0x00000097) @ 0x7e79a250
> ACPI: ASF! (v032 LEGEND I865PASF 0x00000001 INTL 0x20060113) @ 0x7e79a288
> ACPI: GSCI (v001 MSTEST GMCHSCI 0x03000719 MSFT 0x00000097) @ 0x7e79e0c0
> ACPI: SSDT (v001 AMI CPU1PM 0x00000001 INTL 0x20060113) @ 0x7e7a00f0
> ACPI: SSDT (v001 AMI CPU2PM 0x00000001 INTL 0x20060113) @ 0x7e7a02b0
> ACPI: DSDT (v001 A0579 A0579000 0x00000000 INTL 0x20060113) @ 0x00000000
> ACPI: PM-Timer IO Port: 0x808
> ACPI: Local APIC address 0xfee00000
> ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
> Processor #0 6:15 APIC version 20
> ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
> Processor #1 6:15 APIC version 20
> ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled)
> ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled)
> ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
> IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
> ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
> ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
> ACPI: IRQ0 used by override.
> ACPI: IRQ2 used by override.
> ACPI: IRQ9 used by override.
> Enabling APIC mode: Flat. Using 1 I/O APICs
> ACPI: HPET id: 0x8086a202 base: 0xfed00000
> Using ACPI (MADT) for SMP configuration information
> Allocating PCI resources starting at 80000000 (gap: 7e800000:80600000)
> Detected 1866.736 MHz processor.
> Built 1 zonelists. Total pages: 513985
> Kernel command line: ramdisk_size=100000 init=/etc/init lang=de apm=power-off vga=791 initrd=minirt.gz nomce loglevel=0 libata.atapi_enabled=1 quiet nmi_watchdog=0 BOOT_IMAGE=knoppix BOOT_IMAGE=linux
> mapped APIC to ffffd000 (fee00000)
> mapped IOAPIC to ffffc000 (fec00000)
> Enabling fast FPU save and restore... done.
> Enabling unmasked SIMD FPU exception support... done.
> Initializing CPU#0
> PID hash table entries: 4096 (order: 12, 16384 bytes)
> Console: colour dummy device 80x25
> Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
> Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
> Memory: 2048256k/2072128k available (2748k kernel code, 22668k reserved, 956k data, 336k init, 1154624k highmem)
> virtual kernel memory layout:
> fixmap : 0xffe16000 - 0xfffff000 (1956 kB)
> pkmap : 0xff800000 - 0xffc00000 (4096 kB)
> vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
> lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
> .init : 0xc04a6000 - 0xc04fa000 ( 336 kB)
> .data : 0xc03af3bc - 0xc049e7b4 ( 956 kB)
> .text : 0xc0100000 - 0xc03af3bc (2748 kB)
> Checking if this processor honours the WP bit even in supervisor mode... Ok.
> Using HPET for base-timer
> Calibrating delay using timer specific routine.. 3736.14 BogoMIPS (lpj=7472281)
> Security Framework v1.0.0 initialized
> SELinux: Disabled at boot.
> Capability LSM initialized
> Mount-cache hash table entries: 512
> CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e3bd 00000000 00000001
> monitor/mwait feature present.
> using mwait in idle threads.
> CPU: L1 I cache: 32K, L1 D cache: 32K
> CPU: L2 cache: 4096K
> CPU: Physical Processor ID: 0
> CPU: Processor Core ID: 0
> CPU: After all inits, caps: bfebfbff 20100000 00000000 00000940 0000e3bd 00000000 00000001
> Compat vDSO mapped to ffffe000.
> Checking 'hlt' instruction... OK.
> Checking for popad bug... OK.
> SMP alternatives: switching to UP code
> ACPI: Core revision 20060707
> CPU0: Intel(R) Core(TM)2 CPU 6320 @ 1.86GHz stepping 06
> SMP alternatives: switching to SMP code
> Booting processor 1/1 eip 3000
> Initializing CPU#1
> Calibrating delay using timer specific routine.. 3733.42 BogoMIPS (lpj=7466847)
> CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e3bd 00000000 00000001
> monitor/mwait feature present.
> CPU: L1 I cache: 32K, L1 D cache: 32K
> CPU: L2 cache: 4096K
> CPU: Physical Processor ID: 0
> CPU: Processor Core ID: 1
> CPU: After all inits, caps: bfebfbff 20100000 00000000 00000940 0000e3bd 00000000 00000001
> CPU1: Intel(R) Core(TM)2 CPU 6320 @ 1.86GHz stepping 06
> Total of 2 processors activated (7469.56 BogoMIPS).
> ENABLING IO-APIC IRQs
> ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
> checking TSC synchronization across 2 CPUs: passed.
> Brought up 2 CPUs
> migration_cost=665
> checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
> Freeing initrd memory: 1189k freed
> NET: Registered protocol family 16
> EISA bus registered
> ACPI: bus type pci registered
> PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved
> PCI: Not using MMCONFIG.
> PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=3
> PCI: Using configuration type 1
> Setting up standard PCI resources
> ACPI: Interpreter enabled
> ACPI: Using IOAPIC for interrupt routing
> ACPI: PCI Root Bridge [PCI0] (0000:00)
> PCI: Probing PCI hardware (bus 00)
> Boot video device is 0000:00:02.0
> PCI quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO
> PCI quirk: region 0480-04bf claimed by ICH6 GPIO
> PCI: Transparent bridge - 0000:00:1e.0
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P8._PRT]
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
> ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12 14 15)
> ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11 12 14 15)
> ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
> ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11 12 14 *15)
> ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
> ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 *14 15)
> ACPI: PCI Interrupt Link [LNKG] (IRQs *3 4 5 6 7 10 11 12 14 15)
> ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 *7 10 11 12 14 15)
> Linux Plug and Play Support v0.97 (c) Adam Belay
> pnp: PnP ACPI init
> pnp: PnP ACPI: found 14 devices
> PnPBIOS: Disabled by ACPI PNP
> SCSI subsystem initialized
> libata version 2.00 loaded.
> PCI: Using ACPI for IRQ routing
> PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
> NetLabel: Initializing
> NetLabel: domain hash size = 128
> NetLabel: protocols = UNLABELED CIPSOv4
> NetLabel: unlabeled traffic allowed by default
> pnp: 00:07: ioport range 0x290-0x297 has been reserved
> PCI: Ignore bogus resource 6 [0:0] of 0000:00:02.0
> PCI: Bridge: 0000:00:1c.0
> IO window: disabled.
> MEM window: disabled.
> PREFETCH window: bfe00000-bfefffff
> PCI: Bridge: 0000:00:1c.4
> IO window: a000-afff
> MEM window: ff400000-ff4fffff
> PREFETCH window: disabled.
> PCI: Bridge: 0000:00:1e.0
> IO window: b000-bfff
> MEM window: ff500000-ff5fffff
> PREFETCH window: 80000000-800fffff
> ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 16
> PCI: Setting latency timer of device 0000:00:1c.0 to 64
> ACPI: PCI Interrupt 0000:00:1c.4[A] -> GSI 17 (level, low) -> IRQ 16
> PCI: Setting latency timer of device 0000:00:1c.4 to 64
> PCI: Setting latency timer of device 0000:00:1e.0 to 64
> NET: Registered protocol family 2
> IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
> TCP established hash table entries: 131072 (order: 8, 1572864 bytes)
> TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
> TCP: Hash tables configured (established 131072 bind 65536)
> TCP reno registered
> audit: initializing netlink socket (disabled)
> audit(1183842679.792:1): initialized
> highmem bounce pool size: 64 pages
> Total HugeTLB memory allocated, 0
> VFS: Disk quotas dquot_6.5.1
> Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
> fuse init (API version 7.8)
> fuse distribution version: 2.6.1
> io scheduler noop registered
> io scheduler anticipatory registered
> io scheduler deadline registered (default)
> io scheduler cfq registered
> PCI: Setting latency timer of device 0000:00:1c.0 to 64
> assign_interrupt_mode Found MSI capability
> Allocate Port Service[0000:00:1c.0cie00]
> Allocate Port Service[0000:00:1c.0cie02]
> PCI: Setting latency timer of device 0000:00:1c.4 to 64
> assign_interrupt_mode Found MSI capability
> Allocate Port Service[0000:00:1c.4cie00]
> Allocate Port Service[0000:00:1c.4cie02]
> vesafb: framebuffer at 0xd0000000, mapped to 0xf8880000, using 3072k, total 7616k
> vesafb: mode is 1024x768x16, linelength=2048, pages=3
> vesafb: protected mode interface info at 00ff:44f0
> vesafb: scrolling: redraw
> vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
> Console: switching to colour frame buffer device 128x48
> fb0: VESA VGA frame buffer device
> isapnp: Scanning for PnP cards...
> isapnp: No Plug & Play device found
> Real Time Clock Driver v1.12ac
> floppy0: no floppy controllers found
> RAMDISK driver initialized: 16 RAM disks of 100000K size 1024 blocksize
> Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
> ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
> JMB363: IDE controller at PCI slot 0000:01:00.1
> PCI: Enabling device 0000:01:00.1 (0000 -> 0001)
> ACPI: PCI Interrupt 0000:01:00.1[b] -> GSI 17 (level, low) -> IRQ 16
> JMB363: chipset revision 3
> JMB363: 100% native mode on irq 16
> PCI: Setting latency timer of device 0000:01:00.1 to 64
> ide2: BM-DMA at 0xa400-0xa407, BIOS settings: hdeio, hdfio
> ide3: BM-DMA at 0xa408-0xa40f, BIOS settings: hdgMA, hdhMA
> Probing IDE interface ide2...
> Probing IDE interface ide3...
> Probing IDE interface ide0...
> Probing IDE interface ide1...
> Probing IDE interface ide2...
> Probing IDE interface ide3...
> Loading iSCSI transport class v2.0-724.<7>ahci 0000:01:00.0: version 2.0
> ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 17
> PCI: Setting latency timer of device 0000:01:00.0 to 64
> ahci 0000:01:00.0: AHCI 0001.0000 32 slots 2 ports 3 Gbps 0x3 impl SATA mode
> ahci 0000:01:00.0: flags: 64bit ncq pm led clo pmp pio slum part
> ata1: SATA max UDMA/133 cmd 0xF8828100 ctl 0x0 bmdma 0x0 irq 17
> ata2: SATA max UDMA/133 cmd 0xF8828180 ctl 0x0 bmdma 0x0 irq 17
> scsi0 : ahci
> ata1: SATA link down (SStatus 0 SControl 300)
> scsi1 : ahci
> ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
> ata2.00: ATAPI, max UDMA/100
> ata2.00: configured for UDMA/100
> scsi 1:0:0:0: CD-ROM HL-DT-ST DVDRAM GSA-H62N CL00 PQ: 0 ANSI: 5
> ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
> ata2.00: (irq_stat 0x48000000, interface fatal error)
> ata2.00: tag 0 cmd 0xa0 Emask 0x50 stat 0x51 err 0x64 (ATA bus error)
> ata2: soft resetting port
> ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
> ata2.00: configured for UDMA/100
> ata2: EH complete
> sr0: scsi3-mmc drive: 125x/125x writer dvd-ram cd/rw xa/form2 cdda tray
> Uniform CD-ROM driver Revision: 3.20
> sr 1:0:0:0: Attached scsi CD-ROM sr0
> ata_piix 0000:00:1f.2: version 2.00ac6
> ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
> ACPI: PCI Interrupt 0000:00:1f.2[b] -> GSI 19 (level, low) -> IRQ 18
> PCI: Setting latency timer of device 0000:00:1f.2 to 64
> ata3: SATA max UDMA/133 cmd 0xE880 ctl 0xE802 bmdma 0xE080 irq 18
> ata4: SATA max UDMA/133 cmd 0xE480 ctl 0xE402 bmdma 0xE088 irq 18
> scsi2 : ata_piix
> ata3.00: ATA-7, max UDMA/133, 625142448 sectors: LBA48 NCQ (depth 0/32)
> ata3.00: ata3: dev 0 multi count 16
> ata3.00: configured for UDMA/133
> scsi3 : ata_piix
> ata4.00: ATA-7, max UDMA/133, 625142448 sectors: LBA48 NCQ (depth 0/32)
> ata4.00: ata4: dev 0 multi count 16
> ata4.00: configured for UDMA/133
> scsi 2:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5
> SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
> sda: Write Protect is off
> sda: Mode Sense: 00 3a 00 00
> SCSI device sda: drive cache: write back
> SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
> sda: Write Protect is off
> sda: Mode Sense: 00 3a 00 00
> SCSI device sda: drive cache: write back
> sda: sda1 sda2 sda3
> sd 2:0:0:0: Attached scsi disk sda
> scsi 3:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5
> SCSI device sdb: 625142448 512-byte hdwr sectors (320073 MB)
> sdb: Write Protect is off
> sdb: Mode Sense: 00 3a 00 00
> SCSI device sdb: drive cache: write back
> SCSI device sdb: 625142448 512-byte hdwr sectors (320073 MB)
> sdb: Write Protect is off
> sdb: Mode Sense: 00 3a 00 00
> SCSI device sdb: drive cache: write back
> sdb: sdb1 sdb2 sdb3
> sd 3:0:0:0: Attached scsi disk sdb
> ata_piix 0000:00:1f.5: MAP [ P0 P2 P1 P3 ]
> ACPI: PCI Interrupt 0000:00:1f.5[b] -> GSI 19 (level, low) -> IRQ 18
> PCI: Setting latency timer of device 0000:00:1f.5 to 64
> ata5: SATA max UDMA/133 cmd 0xD080 ctl 0xD002 bmdma 0xC800 irq 18
> ata6: SATA max UDMA/133 cmd 0xCC00 ctl 0xC882 bmdma 0xC808 irq 18
> scsi4 : ata_piix
> ata5.00: ATA-7, max UDMA/133, 625142448 sectors: LBA48 NCQ (depth 0/32)
> ata5.00: ata5: dev 0 multi count 16
> ata5.00: configured for UDMA/133
> scsi5 : ata_piix
> ATA: abnormal status 0x7F on port 0xCC07
> scsi 4:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5
> SCSI device sdc: 625142448 512-byte hdwr sectors (320073 MB)
> sdc: Write Protect is off
> sdc: Mode Sense: 00 3a 00 00
> SCSI device sdc: drive cache: write back
> SCSI device sdc: 625142448 512-byte hdwr sectors (320073 MB)
> sdc: Write Protect is off
> sdc: Mode Sense: 00 3a 00 00
> SCSI device sdc: drive cache: write back
> sdc: sdc1 sdc2 sdc3
> sd 4:0:0:0: Attached scsi disk sdc
> PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
> PNP: PS/2 controller doesn't have AUX irq; using default 12
> serio: i8042 KBD port at 0x60,0x64 irq 1
> serio: i8042 AUX port at 0x60,0x64 irq 12
> mice: PS/2 mouse device common for all mice
> EISA: Probing bus 0 at eisa.0
> EISA: Detected 0 cards.
> Initializing XFRM netlink socket
> NET: Registered protocol family 1
> NET: Registered protocol family 15
> Using IPI No-Shortcut mode
> ACPI: (supports S0 S1 S3 S4 S5)
> Time: tsc clocksource has been installed.
> input: AT Translated Set 2 keyboard as /class/input/input0
> RAMDISK: Compressed image found at block 0
> VFS: Mounted root (ext2 filesystem).
> Failed initialization of WD-7000 SCSI card!
> usbcore: registered new interface driver usbfs
> usbcore: registered new interface driver hub
> usbcore: registered new device driver usb
> ACPI: PCI Interrupt 0000:00:1a.7[C] -> GSI 18 (level, low) -> IRQ 19
> PCI: Setting latency timer of device 0000:00:1a.7 to 64
> ehci_hcd 0000:00:1a.7: EHCI Host Controller
> ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
> ehci_