SEO

Hi!

I've tried to install OpenBSD 4.3 on a pc but unfortunately was not able
to boot neither the i386 nor the amd64 install43 CD.
The PC is a Intel D201GLY2
(http://www.intel.com/products/mother...GLY2/index.htm) mainboard
(Celeron 220 @ 1.2 ghz) with a CDROM and a 10GB (western digital) hd on
the IDE-port. Furthermore there is a SATA-harddisk (samsung 500GB)
connected on the first SATA-port and a IDE-controller (Sil 0680) plugged
into the PCI port (with a western digital 250GB harddisk).

After some attempts to install OpenBSD I was able to successfully
install Debian Etch and run "lspci -vv" on it. The output of this can be
found below to get some more information about the system. The FreeBSD
7.0 cdrom is also able to boot this machine, but I've not tried to
install it on the system.

My question is: Is there a possibility to install OpenBSD on this
machine? If yes how can I do this?

I would be glad if someone could please help me.

Best regards,
Christoph


Here are the things I've tried:

*) When booting the i386 CD (after pressing the reset-button) I get the
message:

CD-ROM: 90
Loading /4.3/AMD64/CDBOOT
probing: pc0 mem[639K 944M 11M 532K a20=on]
disk: hd0+* hd1+

(then the screen gets cleared and the following occours

trap: 0(0): invalid opcode fault
cn_tab=0x4ae40
eax 4a023 ecx 1 edx 4a023 ebx 0
esp ff58 ebp 0 esi 0 edi 0
eip 3 eflags 10007 cs 8 ss 10
ds 10 es 10 fs 10 gs 10
Code dump [0x3]:
....
....
....


*) When booting the amd64 CD after pushing the reset-button, I get a
freeze at

CD-ROM: 90
Loading /4.3/AMD64/CDBOOT
probing: pc0 mem[639K 944M 11M 532K a20=on]
disk: hd0+* hd1+

with the cursor after the last '+'

*) When booting the i386 CD or the amd64 CD after power off, the problem
above doesn't occour and the disk-line says:
disk: hd0+* hd1+* hd2* cd0
and starts booting. After a few seconds it hangs with the line
(typewritten, because I've no null-modem-cable):

wd2 at pciide2 channel0 drive 0: <WD2500JB-00GVC0>
wd2: 16-sector PIO, LBA48, 238475MB, 488397168 sectors
wd2(pciide2:0:0): using PIO mode 4, Ultra-DMA mode 5
pciide2: channel 1 configured to native-PCI mode
ppb1 at pci0 dev 31 function 0 "SiS PCI-PCI" rev 0x00
pci2 at ppb1 bus 2
usb1 at ohci0: USB revision 1.0
uhub1 at usb1 "SiS OHCI root hub" rev 1.00/1.00 addr 1
usb2 at ohci0: USB revision 1.0
uhub2 at usb1 "SiS OHCI root hub" rev 1.00/1.00 addr 1
usb3 at ohci0: USB revision 1.0
uhub3 at usb1 "SiS OHCI root hub" rev 1.00/1.00 addr 1
isa0 at mainbus0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
rd0: fixed 4480 blocks
wd0(pciide0:0:1): timeout
type: ata
c_bcount: 512
c_skip: 0
pciide:0:0:1: bus-master DMA error: missing interrupt, status=0x61

Please note that it makes no difference if I plug out the PCI-card
(IDE-controller).
I found a pointer to
http://archives.neohapsis.com/archiv...1-12/1351.html which
helps to avoid the error, but disabling pciide means no harddisks at all.

*) I have successfully installed Debian Etch on this machine and the
output of lspci -vv is:

00:00.0 Host bridge: Silicon Integrated Systems [SiS] Unknown device
0662 (rev 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 128
Region 0: Memory at 48000000 (32-bit, non-prefetchable) [size=32M]
Capabilities: [c0] AGP version 3.5
Status: RQ=32 Iso- ArqSz=2 Cal=3 SBA+ ITACoh- GART64- HTrans- 64bit-
FW+ AGP3+ Rate=x4,x8
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>

00:01.0 PCI bridge: Silicon Integrated Systems [SiS] SiS AGP Port
(virtual PCI-to-PCI bridge) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00001000-00001fff
Memory behind bridge: 4a000000-4a0fffff
Prefetchable memory behind bridge: 40000000-47ffffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-

00:02.0 ISA bridge: Silicon Integrated Systems [SiS] SiS964 [MuTIOL
Media IO] (rev 36)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0

00:02.5 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE] (rev
01) (prog-if 80 [Master])
Subsystem: Intel Corporation Unknown device d61f
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 128
Region 0: I/O ports at <unassigned>
Region 1: I/O ports at <unassigned>
Region 2: I/O ports at <unassigned>
Region 3: I/O ports at <unassigned>
Region 4: I/O ports at 2320 [size=16]
Capabilities: [58] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:02.7 Multimedia audio controller: Silicon Integrated Systems [SiS]
AC'97 Sound Controller (rev a0)
Subsystem: Intel Corporation Unknown device d61f
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 128 (13000ns min, 2750ns max)
Interrupt: pin C routed to IRQ 233
Region 0: I/O ports at 2100 [size=256]
Region 1: I/O ports at 2280 [size=128]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=55mA
PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:03.0 USB Controller: Silicon Integrated Systems [SiS] USB 1.0
Controller (rev 0f) (prog-if 10 [OHCI])
Subsystem: Intel Corporation Unknown device d61f
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (20000ns max)
Interrupt: pin A routed to IRQ 185
Region 0: Memory at 4a104000 (32-bit, non-prefetchable) [size=4K]

00:03.1 USB Controller: Silicon Integrated Systems [SiS] USB 1.0
Controller (rev 0f) (prog-if 10 [OHCI])
Subsystem: Intel Corporation Unknown device d61f
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (20000ns max)
Interrupt: pin B routed to IRQ 193
Region 0: Memory at 4a103000 (32-bit, non-prefetchable) [size=4K]

00:03.2 USB Controller: Silicon Integrated Systems [SiS] USB 1.0
Controller (rev 0f) (prog-if 10 [OHCI])
Subsystem: Intel Corporation Unknown device d61f
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (20000ns max)
Interrupt: pin C routed to IRQ 201
Region 0: Memory at 4a102000 (32-bit, non-prefetchable) [size=4K]

00:03.3 USB Controller: Silicon Integrated Systems [SiS] USB 2.0
Controller (prog-if 20 [EHCI])
Subsystem: Silicon Integrated Systems [SiS] USB 2.0 Controller
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (20000ns max), Cache Line Size: 32 bytes
Interrupt: pin D routed to IRQ 209
Region 0: Memory at 4a101000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:04.0 Ethernet controller: Silicon Integrated Systems [SiS] SiS900 PCI
Fast Ethernet (rev 91)
Subsystem: Intel Corporation Unknown device d61f
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 128 (13000ns min, 2750ns max)
Interrupt: pin A routed to IRQ 217
Region 0: I/O ports at 2000 [size=256]
Region 1: Memory at 4a100000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at 4a120000 [disabled] [size=128K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:05.0 IDE interface: Silicon Integrated Systems [SiS] SATA (rev 01)
(prog-if 85 [Master SecO PriO])
Subsystem: Intel Corporation Unknown device d61f
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 128
Interrupt: pin A routed to IRQ 225
Region 0: I/O ports at 2348 [size=8]
Region 1: I/O ports at 235c [size=4]
Region 2: I/O ports at 2340 [size=8]
Region 3: I/O ports at 2358 [size=4]
Region 4: I/O ports at 2310 [size=16]
Region 5: I/O ports at 2200 [size=128]
Capabilities: [58] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:06.0 RAID bus controller: Silicon Image, Inc. PCI0680 Ultra ATA-133
Host Controller (rev 02)
Subsystem: Silicon Image, Inc. Winic W-680 (Silicon Image 680 based)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 128, Cache Line Size: 4 bytes
Interrupt: pin A routed to IRQ 225
Region 0: I/O ports at 2338 [size=8]
Region 1: I/O ports at 2354 [size=4]
Region 2: I/O ports at 2330 [size=8]
Region 3: I/O ports at 2350 [size=4]
Region 4: I/O ports at 2300 [size=16]
Region 5: Memory at 4a105000 (32-bit, non-prefetchable) [size=256]
Expansion ROM at 4a180000 [disabled] [size=512K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-

00:1f.0 PCI bridge: Silicon Integrated Systems [SiS] PCI-to-PCI bridge
(prog-if 00 [Normal decode])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
Memory behind bridge: 3c000000-3c0fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [d0] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag+
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x16, ASPM L0s L1, Port 0
Link: Latency L0s <1us, L1 <2us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x0
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
Slot: Number 0, PowerLimit 75.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Off, PwrInd Off, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [a0] Message Signalled Interrupts: Mask- 64bit- Queue=0/0
Enable+
Address: fee00000 Data: 40b1
Capabilities: [f4] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

01:00.0 VGA compatible controller: Silicon Integrated Systems [SiS]
661/741/760/761 PCI/AGP VGA Display Adapter (rev 04) (prog-if 00 [VGA])
Subsystem: Intel Corporation Unknown device d61f
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 10
BIST result: 00
Region 0: Memory at 40000000 (32-bit, prefetchable) [size=128M]
Region 1: Memory at 4a000000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at 1000 [size=128]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] AGP version 3.0
Status: RQ=256 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit-
FW- AGP3+ Rate=x4,x8
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>

Hi Christoph!

I had the same problem:
http://groups.google.com/group/comp....f3fb33df6/de97

I have D201GLY and D201GLY2.

Try OpenBSD 4.2 it works on both mainboards.

I didnt try to install OpenBSD 4.3 jet.


Regards,
TomazZ



Christoph Müllner je napisal:
> Hi!
>
> I've tried to install OpenBSD 4.3 on a pc but unfortunately was not able
> to boot neither the i386 nor the amd64 install43 CD.
> The PC is a Intel D201GLY2
> (http://www.intel.com/products/mother...GLY2/index.htm) mainboard
> (Celeron 220 @ 1.2 ghz) with a CDROM and a 10GB (western digital) hd on
> the IDE-port. Furthermore there is a SATA-harddisk (samsung 500GB)
> connected on the first SATA-port and a IDE-controller (Sil 0680) plugged
> into the PCI port (with a western digital 250GB harddisk).
>
> After some attempts to install OpenBSD I was able to successfully
> install Debian Etch and run "lspci -vv" on it. The output of this can be
> found below to get some more information about the system. The FreeBSD
> 7.0 cdrom is also able to boot this machine, but I've not tried to
> install it on the system.
>
> My question is: Is there a possibility to install OpenBSD on this
> machine? If yes how can I do this?
>
> I would be glad if someone could please help me.
>
> Best regards,
> Christoph
>
>
> Here are the things I've tried:
>
> *) When booting the i386 CD (after pressing the reset-button) I get the
> message:
>
> CD-ROM: 90
> Loading /4.3/AMD64/CDBOOT
> probing: pc0 mem[639K 944M 11M 532K a20=on]
> disk: hd0+* hd1+
>
> (then the screen gets cleared and the following occours
>
> trap: 0(0): invalid opcode fault
> cn_tab=0x4ae40
> eax 4a023 ecx 1 edx 4a023 ebx 0
> esp ff58 ebp 0 esi 0 edi 0
> eip 3 eflags 10007 cs 8 ss 10
> ds 10 es 10 fs 10 gs 10
> Code dump [0x3]:
> ...
> ...
> ...
>
>
> *) When booting the amd64 CD after pushing the reset-button, I get a
> freeze at
>
> CD-ROM: 90
> Loading /4.3/AMD64/CDBOOT
> probing: pc0 mem[639K 944M 11M 532K a20=on]
> disk: hd0+* hd1+
>
> with the cursor after the last '+'
>
> *) When booting the i386 CD or the amd64 CD after power off, the problem
> above doesn't occour and the disk-line says:
> disk: hd0+* hd1+* hd2* cd0
> and starts booting. After a few seconds it hangs with the line
> (typewritten, because I've no null-modem-cable):
>
> wd2 at pciide2 channel0 drive 0: <WD2500JB-00GVC0>
> wd2: 16-sector PIO, LBA48, 238475MB, 488397168 sectors
> wd2(pciide2:0:0): using PIO mode 4, Ultra-DMA mode 5
> pciide2: channel 1 configured to native-PCI mode
> ppb1 at pci0 dev 31 function 0 "SiS PCI-PCI" rev 0x00
> pci2 at ppb1 bus 2
> usb1 at ohci0: USB revision 1.0
> uhub1 at usb1 "SiS OHCI root hub" rev 1.00/1.00 addr 1
> usb2 at ohci0: USB revision 1.0
> uhub2 at usb1 "SiS OHCI root hub" rev 1.00/1.00 addr 1
> usb3 at ohci0: USB revision 1.0
> uhub3 at usb1 "SiS OHCI root hub" rev 1.00/1.00 addr 1
> isa0 at mainbus0
> com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
> pckbc0 at isa0 port 0x60/5
> pckbd0 at pckbc0 (kbd slot)
> pckbc0: using irq 1 for kbd slot
> wskbd0 at pckbd0: console keyboard, using wsdisplay0
> rd0: fixed 4480 blocks
> wd0(pciide0:0:1): timeout
> type: ata
> c_bcount: 512
> c_skip: 0
> pciide:0:0:1: bus-master DMA error: missing interrupt, status=0x61
>
> Please note that it makes no difference if I plug out the PCI-card
> (IDE-controller).
> I found a pointer to
> http://archives.neohapsis.com/archiv...1-12/1351.html which
> helps to avoid the error, but disabling pciide means no harddisks at all.
>
> *) I have successfully installed Debian Etch on this machine and the
> output of lspci -vv is:
>
> 00:00.0 Host bridge: Silicon Integrated Systems [SiS] Unknown device
> 0662 (rev 01)
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort+ >SERR- <PERR-
> Latency: 128
> Region 0: Memory at 48000000 (32-bit, non-prefetchable) [size=32M]
> Capabilities: [c0] AGP version 3.5
> Status: RQ=32 Iso- ArqSz=2 Cal=3 SBA+ ITACoh- GART64- HTrans- 64bit-
> FW+ AGP3+ Rate=x4,x8
> Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
>
> 00:01.0 PCI bridge: Silicon Integrated Systems [SiS] SiS AGP Port
> (virtual PCI-to-PCI bridge) (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
> <MAbort- >SERR- <PERR-
> Latency: 0, Cache Line Size: 64 bytes
> Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
> I/O behind bridge: 00001000-00001fff
> Memory behind bridge: 4a000000-4a0fffff
> Prefetchable memory behind bridge: 40000000-47ffffff
> Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
> <MAbort+ <SERR- <PERR-
> BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
>
> 00:02.0 ISA bridge: Silicon Integrated Systems [SiS] SiS964 [MuTIOL
> Media IO] (rev 36)
> Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
>
> 00:02.5 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE] (rev
> 01) (prog-if 80 [Master])
> Subsystem: Intel Corporation Unknown device d61f
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 128
> Region 0: I/O ports at <unassigned>
> Region 1: I/O ports at <unassigned>
> Region 2: I/O ports at <unassigned>
> Region 3: I/O ports at <unassigned>
> Region 4: I/O ports at 2320 [size=16]
> Capabilities: [58] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:02.7 Multimedia audio controller: Silicon Integrated Systems [SiS]
> AC'97 Sound Controller (rev a0)
> Subsystem: Intel Corporation Unknown device d61f
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 128 (13000ns min, 2750ns max)
> Interrupt: pin C routed to IRQ 233
> Region 0: I/O ports at 2100 [size=256]
> Region 1: I/O ports at 2280 [size=128]
> Capabilities: [48] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=55mA
> PME(D0-,D1-,D2-,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:03.0 USB Controller: Silicon Integrated Systems [SiS] USB 1.0
> Controller (rev 0f) (prog-if 10 [OHCI])
> Subsystem: Intel Corporation Unknown device d61f
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR+ FastB2B-
> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 64 (20000ns max)
> Interrupt: pin A routed to IRQ 185
> Region 0: Memory at 4a104000 (32-bit, non-prefetchable) [size=4K]
>
> 00:03.1 USB Controller: Silicon Integrated Systems [SiS] USB 1.0
> Controller (rev 0f) (prog-if 10 [OHCI])
> Subsystem: Intel Corporation Unknown device d61f
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR+ FastB2B-
> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 64 (20000ns max)
> Interrupt: pin B routed to IRQ 193
> Region 0: Memory at 4a103000 (32-bit, non-prefetchable) [size=4K]
>
> 00:03.2 USB Controller: Silicon Integrated Systems [SiS] USB 1.0
> Controller (rev 0f) (prog-if 10 [OHCI])
> Subsystem: Intel Corporation Unknown device d61f
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR+ FastB2B-
> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 64 (20000ns max)
> Interrupt: pin C routed to IRQ 201
> Region 0: Memory at 4a102000 (32-bit, non-prefetchable) [size=4K]
>
> 00:03.3 USB Controller: Silicon Integrated Systems [SiS] USB 2.0
> Controller (prog-if 20 [EHCI])
> Subsystem: Silicon Integrated Systems [SiS] USB 2.0 Controller
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR+ FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32 (20000ns max), Cache Line Size: 32 bytes
> Interrupt: pin D routed to IRQ 209
> Region 0: Memory at 4a101000 (32-bit, non-prefetchable) [size=4K]
> Capabilities: [50] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
> PME(D0+,D1-,D2-,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:04.0 Ethernet controller: Silicon Integrated Systems [SiS] SiS900 PCI
> Fast Ethernet (rev 91)
> Subsystem: Intel Corporation Unknown device d61f
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 128 (13000ns min, 2750ns max)
> Interrupt: pin A routed to IRQ 217
> Region 0: I/O ports at 2000 [size=256]
> Region 1: Memory at 4a100000 (32-bit, non-prefetchable) [size=4K]
> Expansion ROM at 4a120000 [disabled] [size=128K]
> Capabilities: [40] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:05.0 IDE interface: Silicon Integrated Systems [SiS] SATA (rev 01)
> (prog-if 85 [Master SecO PriO])
> Subsystem: Intel Corporation Unknown device d61f
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 128
> Interrupt: pin A routed to IRQ 225
> Region 0: I/O ports at 2348 [size=8]
> Region 1: I/O ports at 235c [size=4]
> Region 2: I/O ports at 2340 [size=8]
> Region 3: I/O ports at 2358 [size=4]
> Region 4: I/O ports at 2310 [size=16]
> Region 5: I/O ports at 2200 [size=128]
> Capabilities: [58] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:06.0 RAID bus controller: Silicon Image, Inc. PCI0680 Ultra ATA-133
> Host Controller (rev 02)
> Subsystem: Silicon Image, Inc. Winic W-680 (Silicon Image 680 based)
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 128, Cache Line Size: 4 bytes
> Interrupt: pin A routed to IRQ 225
> Region 0: I/O ports at 2338 [size=8]
> Region 1: I/O ports at 2354 [size=4]
> Region 2: I/O ports at 2330 [size=8]
> Region 3: I/O ports at 2350 [size=4]
> Region 4: I/O ports at 2300 [size=16]
> Region 5: Memory at 4a105000 (32-bit, non-prefetchable) [size=256]
> Expansion ROM at 4a180000 [disabled] [size=512K]
> Capabilities: [60] Power Management version 2
> Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=2 PME-
>
> 00:1f.0 PCI bridge: Silicon Integrated Systems [SiS] PCI-to-PCI bridge
> (prog-if 00 [Normal decode])
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
> <MAbort- >SERR- <PERR-
> Latency: 0, Cache Line Size: 64 bytes
> Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
> Memory behind bridge: 3c000000-3c0fffff
> Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
> <MAbort+ <SERR- <PERR-
> BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
> Capabilities: [d0] Express Root Port (Slot+) IRQ 0
> Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag+
> Device: Latency L0s <64ns, L1 <1us
> Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
> Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
> Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
> Link: Supported Speed 2.5Gb/s, Width x16, ASPM L0s L1, Port 0
> Link: Latency L0s <1us, L1 <2us
> Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
> Link: Speed 2.5Gb/s, Width x0
> Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
> Slot: Number 0, PowerLimit 75.000000
> Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
> Slot: AttnInd Off, PwrInd Off, Power-
> Root: Correctable- Non-Fatal- Fatal- PME-
> Capabilities: [a0] Message Signalled Interrupts: Mask- 64bit- Queue=0/0
> Enable+
> Address: fee00000 Data: 40b1
> Capabilities: [f4] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 01:00.0 VGA compatible controller: Silicon Integrated Systems [SiS]
> 661/741/760/761 PCI/AGP VGA Display Adapter (rev 04) (prog-if 00 [VGA])
> Subsystem: Intel Corporation Unknown device d61f
> Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Interrupt: pin A routed to IRQ 10
> BIST result: 00
> Region 0: Memory at 40000000 (32-bit, prefetchable) [size=128M]
> Region 1: Memory at 4a000000 (32-bit, non-prefetchable) [size=128K]
> Region 2: I/O ports at 1000 [size=128]
> Capabilities: [40] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [50] AGP version 3.0
> Status: RQ=256 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit-
> FW- AGP3+ Rate=x4,x8
> Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>

Christoph M?llner <christophm30@gmail.com> wrote:
> I've tried to install OpenBSD 4.3 on a pc but unfortunately was not able
> to boot neither the i386 nor the amd64 install43 CD.

Since it appears nobody has a solution for you, and, frankly, I don't
really know much$ about hardware, two random ideas:

- any permutation of 'disable acpi' and 'disable apm'. acpi was enabled
by default in 4.3, so that might cause problems. (Use boot -c).
- try again at misc@openbsd.org. There is, at least, a larger audience
there.

Sorry!

Joachim