I just picked up a Sun Netra T1 200.

It seems to have some hardware problem. When you plug it in the repair
light flashes 3 times and then nothing happens. Pressing the power
button does not start the system.

I can access LOMlite and here is what it outputs

LOMlite starting up.

CPU type: H8/3437S, mode 3
Ram-test: 2048 bytes OK
Initialising i2c bus: OK
Searching for EEPROMs: 50(cfg)
I2c eeprom @50: OK
i2c bus speed code 01... OK
Probing for lm80s: 28
Initialising lm80 @28: OK
Probing for lm75s: none
System functions: PSUs fans breakers rails gpio temps host CLI ebus
clock
Power restored

lom>environment
Fault OFF
Alarm1 OFF
Alarm2 OFF
Alarm3 ON

Fans:
1 fan1 OK standby
2 fan2 OK standby
3 cpu OK standby
4 psu OK standby

PSUs:
1 OK standby

Temperature sensors:
1 Enclosure 29degC OK

Overheat sensors:
1 CPU standby

Circuit breakers:
1 SCSI-Term standby
2 USB0 standby
3 USB1 standby
4 SCC standby

Supply rails:
1 5V standby
2 3V3 standby
3 +12V standby
4 -12V standby
5 CPU core standby
6 +3VSB standby

lom>show
escape #.
model Netra T1 200
hostname netscreen.global.provisioner
power-on-decline off
power-on-delay off
ip-address not set
ip-netmask not set
ip-gateway not set
bootmode normal
rsc-security on
event-reporting on
Time since last boot: +0h2m36s

If I type poweron nothing happens. Any ideas?

Thanks!

We got a T1 200 which pops it fuse in the power cable when the
buildings power goes.

I had this problem before, reset alarm 3 and try it. Thats what worked
for us each time.

michaeldale@gmail.com wrote:
> I just picked up a Sun Netra T1 200.
>
> It seems to have some hardware problem. When you plug it in the repair
> light flashes 3 times and then nothing happens. Pressing the power
> button does not start the system.
>
> I can access LOMlite and here is what it outputs
>
> LOMlite starting up.
>
> CPU type: H8/3437S, mode 3
> Ram-test: 2048 bytes OK
> Initialising i2c bus: OK
> Searching for EEPROMs: 50(cfg)
> I2c eeprom @50: OK
> i2c bus speed code 01... OK
> Probing for lm80s: 28
> Initialising lm80 @28: OK
> Probing for lm75s: none
> System functions: PSUs fans breakers rails gpio temps host CLI ebus
> clock
> Power restored
>
> lom>environment
> Fault OFF
> Alarm1 OFF
> Alarm2 OFF
> Alarm3 ON
>
> Fans:
> 1 fan1 OK standby
> 2 fan2 OK standby
> 3 cpu OK standby
> 4 psu OK standby
>
> PSUs:
> 1 OK standby
>
> Temperature sensors:
> 1 Enclosure 29degC OK
>
> Overheat sensors:
> 1 CPU standby
>
> Circuit breakers:
> 1 SCSI-Term standby
> 2 USB0 standby
> 3 USB1 standby
> 4 SCC standby
>
> Supply rails:
> 1 5V standby
> 2 3V3 standby
> 3 +12V standby
> 4 -12V standby
> 5 CPU core standby
> 6 +3VSB standby
>
> lom>show
> escape #.
> model Netra T1 200
> hostname netscreen.global.provisioner
> power-on-decline off
> power-on-delay off
> ip-address not set
> ip-netmask not set
> ip-gateway not set
> bootmode normal
> rsc-security on
> event-reporting on
> Time since last boot: +0h2m36s
>
> If I type poweron nothing happens. Any ideas?
>
> Thanks!

Yeah that still doesn't seem to fix it

kangcool wrote:

> We got a T1 200 which pops it fuse in the power cable when the
> buildings power goes.
>
> I had this problem before, reset alarm 3 and try it. Thats what worked
> for us each time.
>
> michaeldale@gmail.com wrote:
> > I just picked up a Sun Netra T1 200.
> >
> > It seems to have some hardware problem. When you plug it in the repair
> > light flashes 3 times and then nothing happens. Pressing the power
> > button does not start the system.
> >
> > I can access LOMlite and here is what it outputs
> >
> > LOMlite starting up.
> >
> > CPU type: H8/3437S, mode 3
> > Ram-test: 2048 bytes OK
> > Initialising i2c bus: OK
> > Searching for EEPROMs: 50(cfg)
> > I2c eeprom @50: OK
> > i2c bus speed code 01... OK
> > Probing for lm80s: 28
> > Initialising lm80 @28: OK
> > Probing for lm75s: none
> > System functions: PSUs fans breakers rails gpio temps host CLI ebus
> > clock
> > Power restored
> >
> > lom>environment
> > Fault OFF
> > Alarm1 OFF
> > Alarm2 OFF
> > Alarm3 ON
> >
> > Fans:
> > 1 fan1 OK standby
> > 2 fan2 OK standby
> > 3 cpu OK standby
> > 4 psu OK standby
> >
> > PSUs:
> > 1 OK standby
> >
> > Temperature sensors:
> > 1 Enclosure 29degC OK
> >
> > Overheat sensors:
> > 1 CPU standby
> >
> > Circuit breakers:
> > 1 SCSI-Term standby
> > 2 USB0 standby
> > 3 USB1 standby
> > 4 SCC standby
> >
> > Supply rails:
> > 1 5V standby
> > 2 3V3 standby
> > 3 +12V standby
> > 4 -12V standby
> > 5 CPU core standby
> > 6 +3VSB standby
> >
> > lom>show
> > escape #.
> > model Netra T1 200
> > hostname netscreen.global.provisioner
> > power-on-decline off
> > power-on-delay off
> > ip-address not set
> > ip-netmask not set
> > ip-gateway not set
> > bootmode normal
> > rsc-security on
> > event-reporting on
> > Time since last boot: +0h2m36s
> >
> > If I type poweron nothing happens. Any ideas?
> >
> > Thanks!