SEO

When running mk_kernel, I get the following error messages:

Generating module: tnsmbmx...
Error: 0, file: /stand/build/mod_wk.d/tnsmbmx/lmod.o Fixup error:
Relocation applied to a PA2.0 instruction
som2elf : unknown reloc instruction (ERROR)
*** Error exit code 7

Stop.
config: make did an exit(1)


This is on a 9000 server 800 series with HP-UX 11.0, with PA 1.0 RISC
and only trying to change the MAXUSER from 32 to 64. Any help or
places to start looking?

Rob Mottishaw
Idaho State University
Programmer Analyst

mottrobe@gmail.com <mottrobe@gmail.com> wrote:
> This is on a 9000 server 800 series with HP-UX 11.0, with PA 1.0
> RISC and only trying to change the MAXUSER from 32 to 64. Any help
> or places to start looking?

I would start with how you have a PA-RISC 1.0 system running 11.0 in
the first place since HP-UX 10.10 was the last OS to "support" PA-RISC
1.0 systems and I think 10.20 was the last OS that may have "worked"
on a PA-RISC 1.0 system.

Are you sure you don't have a PA 1.1 system instead?

What does the model command report - 9000/800 is a bit on the vague
side.

The usual song and dance about being up on all the latest patches may
apply.

rick jones
--
firebug n, the idiot who tosses a lit cigarette out his car window
these opinions are mine, all mine; HP might not want them anyway...
feel free to post, OR email to rick.jones2 in hp.com but NOT BOTH...

: Error: 0, file: /stand/build/mod_wk.d/tnsmbmx/lmod.o Fixup error:
: Relocation applied to a PA2.0 instruction
: som2elf : unknown reloc instruction (ERROR)
: Any help or places to start looking?
: Rob Mottishaw

What Rick said.
Also, what does the following return?
$ file /stand/build/mod_wk.d/tnsmbmx/lmod.o

Shame on me for not doing my homework and listening to someone else.
Here's the output from uname:

HP-UX *** B.11.00 U 9000/802

And the processor is PA RISC 2.0. This system was conceived last May
and has been patched with all the latest bundles and patches. Any
suggestions on how to get the kernel to compile? Again the error was:

Generating module: tnsmbmx...
Error: 0, file: /stand/build/mod_wk.d/tnsmbmx/lmod.o Fixup error:
Relocation applied to a PA2.0 instruction
som2elf : unknown reloc instruction (ERROR)
*** Error exit code 7

Stop.
config: make did an exit(1)

Thanks,
Rob

And the output of file /stand/build/mod_wk.d/tnsmbmx/lmod.o is
/stand/build/mod_wk.d/tnsmbmx/lmod.o: PA-RISC2.0 relocatable object

: And the output of file /stand/build/mod_wk.d/tnsmbmx/lmod.o is
: /stand/build/mod_wk.d/tnsmbmx/lmod.o: PA-RISC2.0 relocatable object

It seems this is a PA2.0 32 bit object.
And your kernel is only 32 bit?

: Generating module: tnsmbmx...
: Error: 0, file: /stand/build/mod_wk.d/tnsmbmx/lmod.o Fixup error:
: Relocation applied to a PA2.0 instruction
: som2elf : unknown reloc instruction (ERROR)

Looking at som2elf, it seems that these PA2.0 instructions are not
supported in 32 bit mode: ???

/* PA2.0 instructions */
case 0x14: /* LDD FLDD */
case 0x1c: /* STD FSTD */
case 0x16: /* FLDWM */
case 0x17: /* LDWMC FLDW */
case 0x1e: /* FSTWM */
case 0x1f: /* FSTW STWMC */
case 0x27: case 0x3b: case 0x2f: /* COMDT COMDIB COMBDF*/

Where did the module tnsmbmx come from??

: Looking at som2elf, it seems that these PA2.0 instructions are not
: supported in 32 bit mode: ???

I'm not sure if this patch would help:
PHCO_22899 s700_800 11.00 DLKM configuration tools cumulative patch

You may have to contact the Response Center.

Very good question, where did tnsmbmx come from?

As far as I can tell, it's from TAS (TotalNet Advanced Server), an SMB
server.

And now after wiping the system and re-installing, I'm continuing to
receive the same errors. HP, watch out, here I come!